Panasonic DMRE500 DMRE500 User Guide - Page 74
Recording/Timer recording/Transferring dubbing, The remote control doesn't
View all Panasonic DMRE500 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 74 highlights
Troubleshooting guide Reference Sound No sound. Low volume. Distorted sound. Cannot hear the desired audio type. Cannot switch audio. ≥Check the connections and settings. Check the input mode on the amplifier if you have connected one. ≥Press [AUDIO] to select the audio. ≥Turn off V.S.S. in the following cases. -When using discs that do not have surround sound effects such as Karaoke discs. -When three or more speakers are connected. -When playing MTS broadcast programs. ≥The disc may have restrictions on the method of audio output (e.g. discs for which "D.MIX" is not displayed during play). With some multi-channel discs, unless the number of connected speakers is the same as the disc's channel specification, audio will not be output properly. Refer to the disc's jacket for more information. [DVD-A] ≥You cannot switch the audio in the following cases. -When a DVD-R disc is in the disc tray while DVD drive is selected. -When the recording mode is XP and "Audio for XP Recording" is set to "LPCM". -When "DVD-R High-Speed Recording" is set to "On" ≥You have used digital connection. Set "Dolby Digital" to "PCM" or connect using audio cables (analog connection). ≥There are discs for which audio cannot be changed because of how the disc was created. ≥The audio for the MPEG4 is monaural. Page 7-9, 15, 63 23, 32 39 - - 63 62 63, 9 - - Operation Cannot operate the television. ≥Change manufacturer code. Some televisions cannot be operated even if you change the 14 The remote control doesn't code. work. ≥The remote control and main unit are using different codes. Change the code on the remote 14 control. Press and hold [ENTER] and the indicated number button at the same time for more than 2 seconds. The unit is on but cannot be operated. HDD activation is slow. Cannot eject disc. ≥The batteries are depleted. Replace them with new ones. ≥Colored glass may obstruct the signal reception/transmission. ≥Don't place the signal sensor in direct sunlight or in areas that may be subject to sunlight exposure. ≥Recording drive or playback drive has not been selected properly. ≥Some operations may be prohibited by the disc. ≥The unit is hot ("U14" appears on the display). Wait for "U14" to disappear. ≥One of the unit's safety devices may have been activated. Reset the unit as follows: Press [POWER Í/I] on the main unit to switch the unit to standby. If the unit doesn't switch to standby, press and hold [POWER Í/I] on the main unit for about 10 seconds. The unit is forcibly switched to standby. Alternatively, disconnect the AC power supply cord, wait one minute, then reconnect it. ≥The HDD is in SLEEP mode. ("HDD SLP" appears in the unit's display.) ≥The unit may have a problem. While the unit is off, press and hold [∫] and [CH W] on the main unit at the same time for about 5 seconds. Remove the disc and consult the dealer. 4 - - 22, 30 - - - 79 - Recording/Timer recording/Transferring (dubbing) Cannot record. ≥You haven't inserted a disc or the disc you inserted cannot be recorded on. Insert a disc the unit can record onto. ≥The disc is unformatted. Format the disc. [RAM] ≥The write-protect tab on the cartridge is set to PROTECT, or the disc is protected with DISC SETTING. ≥Some programs have limitations on the number of times they can be recorded. (CPRM) ≥You cannot record when there is not enough space or when the number of titles has reached its limit. Erase unwanted titles. ≥You cannot record on finalized DVD-R discs. ≥Due to peculiarities of DVD-R, you may be unable to record onto them if you either insert and remove the disc or switch the unit on and off while a disc is loaded, a total of fifty times. ≥A DVD-R recorded on this unit may not be recordable on other Panasonic DVD recorders. Timer recording does not work properly. VCR Plusr system does not work properly. ≥The timer program is incorrect or different timer program times overlap. Correct the program. ≥Timer recording program may be deleted if there is an interruption to the power. ≥VCR Plusr system works only after this unit downloads the television program list. Timer recording does not stop ≥Press [∫] and then [ENTER] within 5 seconds. Recording stops. even when [∫] is pressed. The timer program remains even after recording finishes. ≥The timer program remains unless set to "Once". A part or whole of a recorded title has been lost. RQT7394 74 Continued on next page ≥If there is a power failure or the plug is disconnected from the household AC outlet while recording or editing, the title may be lost or the HDD/disc may become unusable. You will have to format the disc ([HDD] [RAM]) or use a new disc. We cannot offer any guarantee regarding lost titles or discs. 20 59 58 68 32, 37, 41, 45, 59 - - - 27 - - 25, 26, 27 25, 26 59