Panasonic PVDV73D PVDV73 User Guide - Page 45

Memory-Stop Editing, DISPLAY, SETUP

Get Panasonic PVDV73D - DIGITAL VIDEO CAMCOR PDF manuals and user guides View all Panasonic PVDV73D manuals
Add to My Manuals
Save this manual to your list of manuals

Page 45 highlights

Editing Features 4, 5PAUSE To listen to the desired audio sound, set the 12bit AUDIO setting of the VCR mode MENU (Menu OSD: p. 108) as follows: 12bit AUDIO:The following selections are available for 12 bit AUDIO dubbed recordings only (sound recorded in SP mode only). ST 1 ST 2 MIX Set this position to listen to the original sound. Set this position to listen to the audio dubbed sound. Set this position to listen to both the original sound and the audio dubbed sound. Note • When a 16 bit recording is dubbed over, the original audio of the recording will be erased. • When a 12 bit recording is dubbed over and played back, and MIX is selected as the AUDIO, both the original audio and the dubbed audio are played back. • If you recorded in LP mode, you cannot use the A.DUB feature. Memory-Stop Editing You can set an automatic Dubbing stop point. DRESET AMENU 4 Press (PAUSE) to start Audio Dubbing. "A.DUB " indication appears. • Connect the Palmcorder to the TV in order to monitor the sound. (p. 38) Only NTSC (National Television Standards Committee) recorded tapes can be audio dubbed. The following screen appears if the tape was not recorded in NTSC format. 5 Press (PAUSE) to stop Audio Dubbing. • If the microphone used for dubbing gets too near the speaker of your TV, a howling noise (feedback) may occur. • If the tape position is in or was started in a blank section, you cannot use the A.DUB feature. A Press MENU to display the VCR FUNCTIONS menu screen. B Rotate JOG KEY to select DISPLAY SETUP , and then press JOG KEY C to display the DISPLAY SETUP menu. Rotate JOG KEY to select C. DISPLAY , and then press JOG KEY to set to MEMORY. D Press MENU to exit MENU mode. Then, press RESET on the remote control to reset the Counter Memory to M 0:00.00. Now, rewind to the editing start point, and continue with steps 2-5. The tape will now stop automatically at "M 0:00.00". Editing Features 45

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
45
Editing Features
Editing Features
4
Press
(PAUSE)
to start Audio
Dubbing. “A.DUB
” indication
appears.
• Connect the Palmcorder to the TV in
order to monitor the sound.
(p. 38)
Only NTSC (National Television Standards
Committee) recorded tapes can be audio
dubbed. The following screen appears if
the tape was not recorded in NTSC format.
5
Press
(PAUSE)
to stop Audio
Dubbing.
To listen to the desired audio sound, set
the 12bit AUDIO setting of the VCR mode
MENU (Menu OSD: p. 108) as follows:
• If the microphone used for dubbing gets
too near the speaker of your TV,
a howling noise (feedback) may occur.
• If the tape position is in or was started in
a blank section, you cannot use the
A.DUB feature.
Memory-Stop Editing
• When a 16 bit recording is dubbed over,
the original audio of the recording will be
erased.
• When a 12 bit recording is dubbed over
and played back, and MIX is selected as
the AUDIO, both the original audio and
the dubbed audio are played back.
• If you recorded in LP mode, you cannot
use the A.DUB feature.
Note
You can set an automatic Dubbing stop
point.
D
RESET
A
MENU
A
Press MENU
to display the VCR
FUNCTIONS menu screen.
B
Rotate JOG KEY
to select
DISPLAY
SETUP
, and then
press JOG KEY
to display the DISPLAY SETUP menu.
C
Rotate JOG KEY
to select
C. DISPLAY
, and then
press JOG
KEY
to set to MEMORY.
D
Press MENU
to exit MENU mode.
Then,
press RESET on the remote
control
to reset the Counter Memory
to M 0:00.00.
Now, rewind to the editing start point
,
and continue with steps 2-5. The tape will
now stop automatically at “M 0:00.00”.
ST 1
ST 2
MIX
Set this position to listen to the
original sound.
Set this position to listen to the
audio dubbed sound.
Set this position to listen to both
the original sound and the audio
dubbed sound.
12bit AUDIO:
The following selections are
available for 12 bit AUDIO dubbed
recordings only (sound recorded in SP
mode only).
4, 5
PAUSE