Panasonic WJ-HDE400/3000T3 Installation Guide - Page 27

unit x: EXTx using the arrow button up or down

Get Panasonic WJ-HDE400/3000T3 PDF manuals and user guides View all Panasonic WJ-HDE400/3000T3 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 27 highlights

6 Move the underscore mark below "YES" using the arrow button (left or right), and then press the [SET] button. 7 Select the device from which the HDD unit is to be removed (network disk recorder: MAIN, extension unit x: EXTx) using the arrow button (up or down), and then press the [SET] button. 10 Remove the HDD units from the extension unit. (1) Hold down the removal knob on the HDD unit. (2) Pull the lever up. (3) Pull the HDD unit out from the HDD slot. Pull the HDD unit out carefully so as not to drop it and handle it gently so as not to give it a shock or vibration. (1) 8 Select the extension unit (EXTx) to be removed using the arrow button (up or down), and then press the [SET] button. 9 Move the underscore mark below "YES" using the arrow button (left or right), and then press the [SET] button. (3) (2) (2) 11 Close the front cover and lock it by pushing and turning the key to the left. Keep the key in a safe place. (2) The shutdown process of the extension unit will start and all the HDD status indicators will start blinking orange. When the shutdown process is complete, the HDD status indicator will go off. • When the shutdown process of the HDD unit on which recording is being performed starts, recording will continue on another HDD unit. Images may sometimes not be recorded for several seconds when switching the HDD unit for recording. If there is only a single HDD unit, recording will stop. When the [SET] button is pressed, the display on the LCD will return to the time and date menu. (1) 12 Check the disk information. The following can be checked on the "Disk information" page on the setup menu of the recorder. Refer to the manuals provided with the recorder for further information. • Total capacity of the hard disk drive • Available (remaining) capacity of the hard disk drive • Hour meter • Operational mode of the hard disk drive • Time and date range of the images recorded on the hard disk drive. Note: • It is impossible to remove the HDD unit using the buttons and the LCD on the front panel when running in the RAID 5 or RAID 6 mode. Refer to page 31 for information on how to replace a faulty hard disk drive. * When using a recorder (not a network disk recorder), refer to the manuals provided with the recorder for how to operate. 27

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
27
10
Remove the HDD units from the extension unit.
(1) Hold down the removal knob on the HDD unit.
(2) Pull the lever up.
(3) Pull the HDD unit out from the HDD slot.
Pull the HDD unit out carefully so as not to drop it and
handle it gently so as not to give it a shock or vibration.
11
Close the front cover and lock it by pushing and
turning the key to the left.
Keep the key in a safe place.
12
Check the disk information.
The following can be checked on the "Disk information"
page on the setup menu of the recorder. Refer to the man-
uals provided with the recorder for further information.
• Total capacity of the hard disk drive
• Available (remaining) capacity of the hard disk drive
• Hour meter
• Operational mode of the hard disk drive
• Time and date range of the images recorded on the
hard disk drive.
Note:
• It is impossible to remove the HDD unit using the buttons
and the LCD on the front panel when running in the RAID 5
or RAID 6 mode. Refer to page 31 for information on how
to replace a faulty hard disk drive.
* When using a recorder (not a network disk recorder), refer to
the manuals provided with the recorder for how to operate.
(3)
(2)
(2)
(1)
(2)
(1)
6
Move the underscore mark below "YES" using the
arrow button (left or right), and then press the [SET]
button.
7
Select the device from which the HDD unit is to be
removed (network disk recorder: MAIN, extension
unit x: EXTx) using the arrow button (up or down),
and then press the [SET] button.
8
Select the extension unit (EXTx) to be removed using
the arrow button (up or down), and then press the
[SET] button.
9
Move the underscore mark below "YES" using the
arrow button (left or right), and then press the [SET]
button.
The shutdown process of the extension unit will start and
all the HDD status indicators will start blinking orange.
When the shutdown process is complete, the HDD status
indicator will go off.
• When the shutdown process of the HDD unit on which
recording is being performed starts, recording will con-
tinue on another HDD unit. Images may sometimes not
be recorded for several seconds when switching the
HDD unit for recording. If there is only a single HDD
unit, recording will stop.
When the [SET] button is pressed, the display on the LCD
will return to the time and date menu.