Panasonic WJ-ND400K Setup Information - Page 40

Site alarm, Site alarm settings

Get Panasonic WJ-ND400K PDF manuals and user guides View all Panasonic WJ-ND400K manuals
Add to My Manuals
Save this manual to your list of manuals

Page 40 highlights

Event Site alarm Use the following procedure to configure settings that control terminal alarm action when a Panasonic alarm protocol alarm (site alarm) is sent from a camera. 1 Click the [Event] button on the setup menu. 2 On the sub-menu that appears, click [Site alarm]. This will display the site alarm setting window. 3 Configure the settings for each item. Refer to "Site alarm settings" table for details about the settings. • To configure the settings of a camera that is not shown on the display, click the applicable camera number range above the [Set] button to change the contents of the display. • Clicking a camera number range saves the currently displayed camera settings. 4 Click the [Set] button. Site alarm settings Item Site alarm Port number (from camera to ND400) Site alarm setup Rec. cam. Preset position Output terminal ♦Initial default Settings Off♦ / On Port number input (1818♦) Cam.1 to Cam.64 / -Signal input (Blank♦) Off / On♦ Description Specifies whether to validate the site alarm. Specifies the port number that receives the site alarm. Specifies the channel of the recording camera. Specifies the preset position (1 to 256) during alarm input. • When this setting is blank, the camera does not move to a preset position. Specifies whether an alarm signal should be output when an event occurs. 40

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
Event
40
Use the following procedure to configure settings that control terminal alarm action when a Panasonic alarm protocol alarm (site alarm) is sent
from a camera.
1
Click the [Event] button on the setup menu.
2
On the sub-menu that appears, click [Site alarm].
This will display the site alarm setting window.
3
Configure the settings for each item.
Refer to “Site alarm settings” table for details about the
settings.
•
To configure the settings of a camera that is not shown on
the display, click the applicable camera number range
above the [Set] button to change the contents of the
display.
•
Clicking a camera number range saves the currently
displayed camera settings.
4
Click the [Set] button.
Site alarm settings
♦
Initial default
Site alarm
Item
Settings
Description
Site alarm
Off
♦
/ On
Specifies whether to validate the site alarm.
Port number
(from camera to ND400)
Port number input
(1818
♦
)
Specifies the port number that receives the site alarm.
Site alarm setup
Rec. cam.
Cam.1 to Cam.64 / --
Specifies the channel of the recording camera.
Preset position
Signal input
(Blank
♦
)
Specifies the preset position (1 to 256) during alarm input.
•
When this setting is blank, the camera does not move to a
preset position.
Output terminal
Off / On
♦
Specifies whether an alarm signal should be output when an
event occurs.