Pioneer DEHP7900BT Owner's Manual - Page 43

Boosting the bass, Using the high pass filter, Adjusting source levels, Adjusting subwoofer settings

Get Pioneer DEHP7900BT - Car In-Dash CD/MP3/WMA/WAV/iTunes AAC Receiver PDF manuals and user guides
UPC - 012562853215
View all Pioneer DEHP7900BT manuals
Add to My Manuals
Save this manual to your list of manuals

Page 43 highlights

Operating this unit Section 02 English Adjusting subwoofer settings When the subwoofer output is on, you can adjust the cut-off frequency and the output level of the subwoofer. 1 Use MULTI-CONTROL to select Sub W.2. # When the subwoofer output is on, you can select Sub W.2. 2 Push MULTI-CONTROL left or right to select cut-off frequency. Each time MULTI-CONTROL is pushed left or right, cut-off frequencies are selected in the following order: 50Hz-63Hz-80Hz-100Hz-125Hz Only frequencies lower than those in the selected range are outputted from the subwoofer. 3 Push MULTI-CONTROL up or down to adjust the output level of the subwoofer. Each time MULTI-CONTROL is pushed up or down, subwoofer level increases or decreases. +6 to -24 is displayed as the level is increased or decreased. HPF (high pass filter). Only frequencies higher than those in the selected range are outputted from the front or rear speakers. 1 Use MULTI-CONTROL to select HPF. 2 Press MULTI-CONTROL to turn high pass filter on. 80Hz appears in the display. High pass filter is now on. # If the high pass filter has been previously adjusted, the frequency of that previously selected will be displayed instead of 80Hz. # To turn high pass filter off, press MULTI-CONTROL again. 3 Push MULTI-CONTROL left or right to select cut-off frequency. Each time MULTI-CONTROL is pushed left or right, cut-off frequencies are selected in the following order: 50Hz-63Hz-80Hz-100Hz-125Hz Only frequencies higher than those in the selected range are outputted from the front or rear speakers. Boosting the bass Bass boost function boosts the bass level of sound lower than 100 Hz. The more the bass level is increased, the more the bass sound is emphasized and the entire sound becomes powerful. When using this function with the subwoofer, the sound under the cut-off frequency is boosted. 1 Use MULTI-CONTROL to select Bass. 2 Push MULTI-CONTROL up or down to select a desired level. 0 to +6 is displayed as the level is increased or decreased. Using the high pass filter When you do not want low sounds from the subwoofer output frequency range to play from the front or rear speakers, turn on the Adjusting source levels SLA (source level adjustment) lets you adjust the volume level of each source to prevent radical changes in volume when switching between sources. ! Settings are based on the FM tuner volume level, which remains unchanged. 1 Compare the FM tuner volume level with the level of the source you wish to adjust. 2 Use MULTI-CONTROL to select SLA. 3 Push MULTI-CONTROL up or down to adjust the source volume. Each time MULTI-CONTROL is pushed up or down, source volume increases or decreases. SLA +4 to SLA -4 is displayed as the source volume is increased or decreased. En 43

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
Adjusting subwoofer settings
When the subwoofer output is on, you can ad-
just the cut-off frequency and the output level
of the subwoofer.
1
Use MULTI-CONTROL to select Sub W.2.
#
When the subwoofer output is on, you can se-
lect
Sub W.2
.
2
Push MULTI-CONTROL left or right to
select cut-off frequency.
Each time
MULTI-CONTROL
is pushed left or
right, cut-off frequencies are selected in the
following order:
50Hz
—
63Hz
—
80Hz
—
100Hz
—
125Hz
Only frequencies lower than those in the se-
lected range are outputted from the subwoo-
fer.
3
Push MULTI-CONTROL up or down to
adjust the output level of the subwoofer.
Each time
MULTI-CONTROL
is pushed up or
down, subwoofer level increases or decreases.
+6
to
–
24
is displayed as the level is increased
or decreased.
Boosting the bass
Bass boost function boosts the bass level of
sound lower than 100 Hz. The more the bass
level is increased, the more the bass sound is
emphasized and the entire sound becomes
powerful. When using this function with the
subwoofer, the sound under the cut-off fre-
quency is boosted.
1
Use MULTI-CONTROL to select Bass.
2
Push MULTI-CONTROL up or down to
select a desired level.
0
to
+6
is displayed as the level is increased or
decreased.
Using the high pass filter
When you do not want low sounds from the
subwoofer output frequency range to play
from the front or rear speakers, turn on the
HPF (high pass filter). Only frequencies higher
than those in the selected range are outputted
from the front or rear speakers.
1
Use MULTI-CONTROL to select HPF.
2
Press MULTI-CONTROL to turn high
pass filter on.
80Hz
appears in the display. High pass filter is
now on.
#
If the high pass filter has been previously ad-
justed, the frequency of that previously selected
will be displayed instead of
80Hz
.
#
To turn high pass filter off, press
MULTI-CONTROL
again.
3
Push MULTI-CONTROL left or right to
select cut-off frequency.
Each time
MULTI-CONTROL
is pushed left or
right, cut-off frequencies are selected in the
following order:
50Hz
—
63Hz
—
80Hz
—
100Hz
—
125Hz
Only frequencies higher than those in the se-
lected range are outputted from the front or
rear speakers.
Adjusting source levels
SLA (source level adjustment) lets you adjust
the volume level of each source to prevent ra-
dical changes in volume when switching be-
tween sources.
!
Settings are based on the FM tuner volume
level, which remains unchanged.
1
Compare the FM tuner volume level
with the level of the source you wish to ad-
just.
2
Use MULTI-CONTROL to select SLA.
3
Push MULTI-CONTROL up or down to
adjust the source volume.
Each time
MULTI-CONTROL
is pushed up or
down, source volume increases or decreases.
SLA +4
to
SLA
–
4
is displayed as the source
volume is increased or decreased.
Operating this unit
En
43
English
Section
02