Sanyo WTC500L Owner's Manual - Page 16

Remote Control Battery Installation, Remote Control Receivers and Operating Range

Get Sanyo WTC500L - WXGA LCD Projector 720p PDF manuals and user guides
UPC - 086483074257
View all Sanyo WTC500L manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

Part Names and Functions Remote Control Battery Installation 1 Open the battery compartment lid. 2 Install new batteries into the compartment. 3 Replace the compartment lid. Press the lid downward and slide it. Two AAA size batteries For correct polarity (+ and -), be sure battery terminals are in contact with pins in the compartment. To ensure safe operation, please observe the following precautions : ● Use two (2) AAA or LR03 type alkaline batteries. ● Always replace batteries in sets. ● Do not use a new battery with a used battery. ● Avoid contact with water or liquid. ● Do not expose the remote control to moisture or heat. ● Do not drop the remote control. ● If the battery has leaked on the remote control, carefully wipe the case clean and install new batteries. ● Risk of an explosion if battery is replaced by an incorrect type. ● Dispose of used batteries according to the instructions. Remote Control Receivers and Operating Range Point the remote control toward the projector (to Infrared 16.4' (5 m) Remote Receivers) when pressing the buttons. Maximum operating range for the remote control is about 16.4' (5 m) and 60 degrees in front and rear of the projector. Infrared Remote Receivers are provided both in front and back of the projector. You can conveniently use both of the receivers (see pages 10, 55). ✔Notes: • When hanging the projector from the ceiling, select the Infrared Remote Receiver which is located farther away from the fluorescent light (p.55). • When using the projector in the horizontal position without hanging from the ceiling, it is recommended to deactivate the top Infrared Remote Receiver to avoid the effects of the fluorescent light (p.55). 16.4' (5 m) Wired Remote Control The remote control can be used as a wired remote control. Wired remote control helps you use the remote control outside of the operating range (16.4'/ 5 m). Connect the remote control and the projector with the remote control cable (sold separately). Connected with the remote control cable, the remote control does not emit wireless signal. 16

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
16
To ensure safe operation, please observe the following precautions :
±
l
Use two (2) AAA or LR03 type alkaline batteries.
±
l
Always replace batteries in sets.
±
l
Do not use a new battery with a used battery.
±
l
Avoid contact with water or liquid.
±
l
Do not expose the remote control to moisture or heat.
±
l
Do not drop the remote control.
±
l
If the battery has leaked on the remote control, carefully wipe the case clean and install new batteries.
±
l
Risk of an explosion if battery is replaced by an incorrect type.
±
l
Dispose of used batteries according to the instructions.
Press the lid
downward and slide it.
Open the battery
compartment lid.
Install new batteries
into the compartment.
Replace the
compartment lid.
Two AAA size batteries
For correct polarity (+ and –),
be sure battery terminals are
in contact with pins in the
compartment.
1
2
3
Point the remote control toward the projector (to Infrared
Remote Receivers) when pressing the buttons. Maximum
operating range for the remote control is about 16.4’ (5 m)
and 60 degrees in front and rear of the projector.
Infrared Remote Receivers are provided both in front and
back of the projector. You can conveniently use both of the
receivers (see pages 10, 55).
Remote Control Receivers and Operating Range
Remote Control Battery Installation
16.4’
(5 m)
16.4’
(5 m)
Part Names and Functions
✔
Notes:
• When hanging the projector from the ceiling, select the
Infrared Remote Receiver which is located farther away
from the fluorescent light (p.55).
• When using the projector in the horizontal position
without hanging from the ceiling, it is recommended to
deactivate the top Infrared Remote Receiver to avoid the
effects of the fluorescent light (p.55).
The remote control can be used as a wired remote control. Wired remote control helps you use the remote control outside
of the operating range (16.4’/ 5 m). Connect the remote control and the projector with the remote control cable (sold
separately). Connected with the remote control cable, the remote control does not emit wireless signal.
Wired Remote Control