Sanyo WTC500L Owner's Manual - Page 55

Pointer, Remote control, To change the code for the projector, RC sensor

Get Sanyo WTC500L - WXGA LCD Projector 720p PDF manuals and user guides
UPC - 086483074257
View all Sanyo WTC500L manuals
Add to My Manuals
Save this manual to your list of manuals

Page 55 highlights

Pointer You can emphasize a part of the projected image with this function. Use the Point ed buttons to choose either Spotlight or Pointer and press the SELECT button. Then use the Point 7 8 buttons to select a size of the Spotlight (Large, Middle, or Small) or a pattern of the Pointer (Arrow, Finger, or Dot). (See page 32 for operation.) Pointer Setting Remote control The eight different remote control codes (Code 1-Code 8) are assigned to the projector; the factory-set, initial code (Code 1) and the other seven codes (Code 2 to Code 8). The same code should be set on both the projector and the remote control. For example, operating the projector in "Code 7", the remote control code also must be switched to "Code 7". To change the code for the projector Select a remote control code in this Setting Menu. To change the code for the remote control Press and hold the MENU button and a number button (1-8) on the remote control for more than five seconds to switch between the codes. (See page 17 for details.) RC sensor Select a location of the infrared remote receiver of the remote control. See "Remote Control Operating Range" on page 16 for details. All A ctivate All of the front, top and back receivers. Front & Top..... Activate the front and top receivers. Top & Back..... Activate the top and back receivers. Front & Back... Activate the front and back receivers. Front Activate only the front receiver. Top Activate only the top receiver. Back Activate only the back receiver. Use the Point ed buttons to choose either Spotlight or Pointer, and then use the Point 7 8 buttons to switch between the options. Remote control ✔Notes: • W hen using the projector in the horizontal position without hanging from the ceiling, it is recommended to deactivate the top Infrared Remote Receiver to avoid the effects of the fluorescent light. • W hen the Standby mode is set to "Eco" in the Setting(p.56), all of the infrared remote receivers are activated regardless of the RC sensor setting. After turning Off and On the projector, the RC sensor setting will be activated . 55

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
55
Setting
Pointer
You can emphasize a part of the projected image with
this function. Use the Point
ed
buttons to choose either
Spotlight or Pointer and press the SELECT button. Then
use the Point
7 8
buttons to select a size of the Spotlight
(Large, Middle, or Small) or a pattern of the Pointer (Arrow,
Finger, or Dot). (See page 32 for operation.)
Pointer
Remote control
Remote control
The eight different remote control codes (Code 1–Code 8)
are assigned to the projector; the factory-set, initial code
(Code 1) and the other seven codes (Code 2 to Code 8).
The same code should be set on both the projector and
the remote control. For example, operating the projector in
“Code 7”
, the remote control code also must be switched to
“Code 7”
.
To change the code for the projector
Select a remote control code in this Setting Menu.
To change the code for the remote control
Press and hold the MENU button and a number button
(1–8) on the remote control for more than five seconds to
switch between the codes. (See page 17 for details.)
RC sensor
Select a location of the infrared remote receiver of the
remote control. See “Remote Control Operating Range”
on page 16 for details.
All
...................
Activate All of the front, top and back
receivers.
Front & Top
.....
Activate the front and top receivers.
Top & Back
.....
Activate the top and back receivers.
Front & Back .. Activate the front and back receivers.
Front
..............
Activate only the front receiver.
Top
................
Activate only the top receiver.
Back
..............
Activate only the back receiver.
Use the Point
ed
buttons
to choose either Spotlight
or Pointer, and then use
the Point
7 8
buttons
to switch between the
options.
✔
Notes:
• When using the projector in the horizontal
position without hanging from the ceiling,
it is recommended to deactivate the top
Infrared Remote Receiver to avoid the
effects of the fluorescent light.
• When the Standby mode is set to “Eco“ in
the Setting(p.56), all of the infrared remote
receivers are activated regardless of the
RC sensor setting. After turning Off and On
the projector, the RC sensor setting will be
activated .