Sanyo WTC500L Owner's Manual - Page 72

Image is Top/Bottom reversed°, Image is Left/Right reversed°

Get Sanyo WTC500L - WXGA LCD Projector 720p PDF manuals and user guides
UPC - 086483074257
View all Sanyo WTC500L manuals
Add to My Manuals
Save this manual to your list of manuals

Page 72 highlights

Appendix - Projecting from the excessive slant angle to the screen may cause keystone distortion and partial imperfect focus. Picture is not bright enough. - Check if "Contrast" or "Brightness" are adjusted properly See page 42. - Check if "Image level" is selected properly See page 41. - Check the LAMP 1/2 REPLACE indicators. If it lights, the end of lamp life is approaching. Replace the lamp with a new one promptly. See pages 66-68, 78. - Check the Lamp control function See page 54. The color is strange. - Check the Input signal, color system, video system, or computer system mode. - Adjust the Image level properly. See page 41. Image is Left/Right reversed. Image is Top/Bottom reversed. - Check the Ceiling/Rear function. See page 45. - Check the Ceiling function. See page 45. The image is distorted or runs off. - Check the "PC Adjustment" menu or "Screen" menu and adjust them. See pages 37-40, 45-48. The edge of image is distorted. - With maximum lens shift, image distortion may be observed. No sound - Check the audio cable connection from audio input source. - Adjust the audio source. - Press the Volume + button. See page 29. - Press the Mute button. See page 29. - When the AUDIO OUT is plugged in, the projector's built-in speaker is not available. See page 22. - Is the image projected? You will hear the sound only when the image is projected. Auto PC adjustment function - Check the Input signal. Auto PC Adjustment function can not work, does not work. when 480p, 575p, 720p, 480i, 575i, 1035i, or 1080i is selected. See page 38. - The Auto adj. icon turns gray and cannot be operated with the digital signals. See page 38. Some displays are not seen during the operation. - Check the Display function. See page 56. The setting does not remain after - Make sure you selected "Store" after adjusting settings. Some settings turning off power. cannot be stored if not registered with "Store." Power management function does - Power management function cannot work while "Freeze" function is not work. running or the shutter is closed. Image disappears automatically - Check the power management function in the Setting. The power management is set to "On" at the factory. 72

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
72
– Projecting from the excessive slant angle to the screen may cause
keystone distortion and partial imperfect focus.
Picture is not bright enough°
– Check if "Contrast" or "Brightness" are adjusted properly See page 42.
– Check if "Image level" is selected properly See page 41.
–
Check the LAMP 1/2 REPLACE indicators. If it lights, the end of lamp
life is approaching. Replace the lamp with a new one promptly. See
pages 66-68, 78.
– Check the Lamp control function See page 54.
The color is strange°
–
Check the Input signal, color system, video system, or computer
system mode.
– Adjust the Image level properly. See page 41.
Image is Left/Right reversed°
– Check the Ceiling/Rear function. See page 45.
Image is Top/Bottom reversed°
– Check the Ceiling function. See page 45.
The image is distorted or runs off°
– Check the "PC Adjustment" menu or "Screen" menu and adjust them.
See pages 37-40, 45-48.
The edge of image is distorted°
– With maximum lens shift, image distortion may be observed.
No sound
– Check the audio cable connection from audio input source.
– Adjust the audio source.
– Press the Volume + button. See page 29.
– Press the Mute button. See page 29.
– When the AUDIO OUT is plugged in, the projector's built-in speaker is
not available. See page 22.
– Is the image projected? You will hear the sound only when the image is
projected.
Auto PC adjustment function
– Check the Input signal. Auto PC Adjustment function can not work,
does not work°
when 480p, 575p, 720p, 480i, 575i, 1035i, or 1080i is selected.
See page 38.
– The Auto adj. icon turns gray and cannot be operated with the digital
signals. See page 38.
Some displays are not seen
– Check the Display function. See page 56.
during the operation°
The setting does not remain after
– Make sure you selected "Store" after adjusting settings. Some settings
turning off power°
cannot be stored if not registered with "Store."
Power management function does
– Power management function cannot work while "Freeze" function is
not work°
running or the shutter is closed.
Image disappears automatically
– Check the power management function in the Setting. The power
management is set to “On” at the factory.
Appendix