Sharp PG-B10S Operation Manual - Page 70

Removing and Installing the Lamp Unit, standby mode. - user manual

Get Sharp PG-B10S - SVGA LCD Projector PDF manuals and user guides
UPC - 074000364080
View all Sharp PG-B10S manuals
Add to My Manuals
Save this manual to your list of manuals

Page 70 highlights

Regarding the Lamp Removing and Installing Lamp the Lamp Unit unit BQC-PGB10S//1 Info • Be sure to remove the lamp unit using the handle. Be sure not to touch the glass surface of the lamp unit or the inside of the projector. • To avoid injury to yourself and damage to the lamp, be sure to carefully follow the steps below. • Do not loosen other screws except for the lamp unit cover and lamp unit. • Please refer to the installation manual included with the lamp unit. 1 Press on the projector STANDBY or on the remote control to put the projector into the standby mode. • Wait until the cooling fan stops. Warning! • Do not remove the lamp unit from the projector right after use. The lamp will be very hot and may cause burn or injury. STANDBY button STANDBY STANDBY button 2 Disconnect the power cord. • Unplug the power cord from the AC socket. • Leave the lamp until it has fully cooled down (about 1 hour). 3 Change the air filter. • Change the air filter whenever you install the lamp unit (see pages 61 and 62). 4 Remove the lamp unit cover. • Turn the projector over. Loosen the user service screw (1) that secures the lamp unit cover. Pressing the tab, remove the lamp unit cover (2). AC socket User service screw Tab 1 2 -66

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
-66
Lamp
unit
BQC-PGB10S//1
Removing and Installing
the Lamp Unit
Info
•
Be sure to remove the lamp unit using the
handle. Be sure not to touch the glass sur-
face of the lamp unit or the inside of the
projector.
•
To avoid injury to yourself and damage to
the lamp, be sure to carefully follow the
steps below.
•
Do not loosen other screws except for the
lamp unit cover and lamp unit.
•
Please refer to the installation manual in-
cluded with the lamp unit.
1
Press
on the projector
or
STANDBY
on the remote control to
put the projector into the
standby mode.
•
Wait until the cooling fan stops.
Warning!
•
Do not remove the lamp unit from the
projector right after use. The lamp will
be very hot and may cause burn or
injury.
2
Disconnect the power cord.
•
Unplug the power cord from the AC
socket.
•
Leave the lamp until it has fully cooled
down (about 1 hour).
3
Change the air filter.
•
Change the air filter whenever you in-
stall the lamp unit (see pages
61
and
62
).
4
Remove the lamp unit cover.
•
Turn the projector over. Loosen the user
service screw (
1
) that secures the lamp
unit cover. Pressing the tab, remove the
lamp unit cover (
2
).
1
2
AC socket
Tab
User
service screw
STANDBY button
STANDBY
button
STANDBY
Regarding the Lamp