Singer One Instruction Manual 2 - Page 24

side`of

Get Singer One PDF manuals and user guides View all Singer One manuals
Add to My Manuals
Save this manual to your list of manuals

Page 24 highlights

22 To Set the Needle Turn the balance wheel over toward you until the needle bar moves up to its highest point; loosen the thumb screw (B, Fig. 15, page17) in the needle clamp (G, Fig. 15) and put the needle up into the clamp as far .as it will go, with the flat side`of its shank toward the right, then tighten the thumb screw. To select the correct needle, see page 53. To Thread the Needle (SEE FIG. 22 ON THE FOLLOWING PAGE) Turn the balance wheel over toward you until the thread take-up lever (5) is raised to its highest point. Place the spool of thread on the spool pin at the top of the machine; pass the thread into the thread guide (1) at the left, down, under and from right to left between the tension discs (2). Hold the spool tightly in the right hand and with the left hand pull the thread up under the thread take-up spring (4) until it enters the retaining fork (3), then pass the thread up and from right to left through the hole (5) in the end of the thread take-up lever, down into the eyelet (6) at the front of the face plate, into the lower wire thread guide (7), then from left to right through the eye of the needle (8). Draw about two inches of thread through the eye of the needle with which to commence sewing.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
22
To
Set
the
Needle
Turn
the
balance
wheel
over
toward
you
until
the
needle
bar
moves
up
to
its
highest
point;
loosen
the
thumb
screw
(B,
Fig.
15,
page17)
in
the
needle
clamp
(G,
Fig.
15)
and
put
the
needle
up
into
the
clamp
as
far
.as
it
will
go,
with
the
flat
side`of
its
shank
toward
the
right,
then
tighten
the
thumb
screw.
To
select
the
correct
needle,
see
page
53.
To
Thread
the
Needle
(SEE
FIG.
22
ON
THE
FOLLOWING
PAGE)
Turn
the
balance
wheel
over
toward
you
until
the
thread
take-up
lever
(5)
is
raised
to
its
highest
point.
Place
the
spool
of
thread
on
the
spool
pin
at
the
top
of
the
machine;
pass
the
thread
into
the
thread
guide
(1)
at
the
left,
down,
under
and
from
right
to
left
between
the
tension
discs
(2).
Hold
the
spool
tightly
in
the
right
hand
and
with
the
left
hand
pull
the
thread
up
under
the
thread
take-up
spring
(4)
until
it
enters
the
retaining
fork
(3),
then
pass
the
thread
up
and
from
right
to
left
through
the
hole
(5)
in
the
end
of
the
thread
take-up
lever,
down
into
the
eyelet
(6)
at
the
front
of
the
face
plate,
into
the
lower
wire
thread
guide
(7),
then
from
left
to
right
through
the
eye
of
the
needle
(8).
Draw
about
two
inches
of
thread
through
the
eye
of
the
needle
with
which
to
commence
sewing.