Singer One Instruction Manual 2 - Page 31

screwdriver.

Get Singer One PDF manuals and user guides View all Singer One manuals
Add to My Manuals
Save this manual to your list of manuals

Page 31 highlights

29 bin case bearing, as indicated by arrows in Fig. 28, then replace the bobbin and slide plate. To oil movable parts in the head of the machine, take out the screw (B, Fig. 27) near the lower end of the face plate and loosen the screw (A, Fig. 27) A 7.; Fig. 29. END VIEW, SHOWING OILING POINTS near the upper end of the face plate, then raise the plate and slip it off over the head of the screw (A). Put one drop of oil into each of the holes and joints thus uncovered, as shown in Fig. 29. The gears of the motor should occasionally be lubricated with grease from the tube of. SINGER MOTOR LUBRICANT which is furnished with the machine. Unscrew the spool pin (E, Fig. 27)-a slot being cut at the top of the spool pin to permit the use of a screwdriver. After removing the spool pin and felt washer (D, Fig. 27) insert the tip of the motor lubricant tube into the spool pin hole and force a small quantity of the lubricant through the hole to lubricate the gears, then replace the spool pin and felt washer. Under no circumstances should oil be used at this hole, but only the lubricant.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
29
bin
case
bearing,
as
indicated
by
arrows
in
Fig.
28,
then
replace
the
bobbin
and
slide
plate.
To
oil
movable
parts
in
the
head
of
the
machine,
take
out
the
screw
(B,
Fig.
27)
near
the
lower
end
of
the
face
plate
and
loosen
the
screw
(A,
Fig.
27)
A
7.;
Fig.
29.
END
VIEW,
SHOWING
OILING
POINTS
near
the
upper
end
of
the
face
plate,
then
raise
the
plate
and
slip
it
off
over
the
head
of
the
screw
(A).
Put
one
drop
of
oil
into
each
of
the
holes
and
joints
thus
uncovered,
as
shown
in
Fig.
29.
The
gears
of
the
motor
should
occasionally
be
lubricated
with
grease
from
the
tube
of.
SINGER
MOTOR
LUBRICANT
which
is
furnished
with
the
machine.
Unscrew
the
spool
pin
(E,
Fig.
27)—a
slot
being
cut
at
the
top
of
the
spool
pin
to
permit
the
use
of
a
screwdriver.
After
removing
the
spool
pin
and
felt
washer
(D,
Fig.
27)
insert
the
tip
of
the
motor
lubricant
tube
into
the
spool
pin
hole
and
force
a
small
quantity
of
the
lubricant
through
the
hole
to
lubricate
the
gears,
then
replace
the
spool
pin
and
felt
washer.
Under
no
circumstances
should
oil
be
used
at
this
hole,
but
only
the
lubricant.