Singer One Instruction Manual 2 - Page 50

attachment

Get Singer One PDF manuals and user guides View all Singer One manuals
Add to My Manuals
Save this manual to your list of manuals

Page 50 highlights

48 edge of the ruffle to the right of the attachment as shown in Fig. 46. The material for piping must measure about AI inch wide when folded in the centre and is usually cut on the bias. Place the piping material in the ruttier, following the line 4, in Fig. 42, with the foldededge of the piping to the right. The material to which the piping and ruffling are to be sewn should be folded on the edge and inserted in the ruttier, following the line 5, in Fig. 42. To Adjust the Ruffler for Plaiting Raise the adjusting lever (E, Fig. 47) and move it to the right so that the projection (D, Fig. 47) C grf • ao sx FIG. 47 will enter the slot marked "6" in the adjusting lever when the lever is released. The ruffling blade will then move forward and back once at every six stitches. To adjust the ruffling blade to make a plait once at every twelve stitches, place the adjusting lever (E, Fig. 47) so that the projection (D) enters the slot marked "12" in the adjusting lever. Insert the material to be plaited between the two blue blades, following the line 2, Fig. 42. The size or width of plaits is regulated by the adjusting screw

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
48
edge
of
the
ruffle
to
the
right
of
the
attachment
as
shown
in
Fig.
46.
The
material
for
piping
must
measure
about
AI
inch
wide
when
folded
in
the
centre
and
is
usually
cut
on
the
bias.
Place
the
piping
material
in
the
ruttier,
following
the
line
4,
in
Fig.
42,
with
the
foldededge
of
the
piping
to
the
right.
The
material
to
which
the
piping
and
ruffling
are
to
be
sewn
should
be
folded
on
the
edge
and
inserted
in
the
ruttier,
following
the
line
5,
in
Fig.
42.
To
Adjust
the
Ruffler
for
Plaiting
Raise
the
adjusting
lever
(E,
Fig.
47)
and
move
it
to
the
right
so
that
the
projection
(D,
Fig.
47)
C
grf
•
ao
sx
FIG.
47
will
enter
the
slot
marked
"6"
in
the
adjusting
lever
when
the
lever
is
released.
The
ruffling
blade
will
then
move
forward
and
back
once
at
every
six
stitches.
To
adjust
the
ruffling
blade
to
make
a
plait
once
at
every
twelve
stitches,
place
the
adjust-
ing
lever
(E,
Fig.
47)
so
that
the
projection
(D)
enters
the
slot
marked
"12"
in
the
adjusting
lever.
Insert
the
material
to
be
plaited
between
the
two
blue
blades,
following
the
line
2,
Fig.
42.
The
size
or
width
of
plaits
is
regulated
by
the
adjusting
screw