Sony DG910 Instructions Manual - Page 36

To cancel Auto Calibration, Confirming/saving the, measurement results

Get Sony DG910 - STR AV Receiver PDF manuals and user guides
UPC - 027242707023
View all Sony DG910 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 36 highlights

Press AUTO CAL. Measurement starts in 5 seconds and the display changes as follows: A. CAL [5] t A. CAL [4] t A. CAL [3] t A. CAL [2] t A. CAL [1] The measurement process will take approximately 30 seconds to complete. The table below shows the display when measurement starts. Measurement for Display Speaker existance TONE Speaker gain, distance, frequency T.S.P. response Sub woofer gain and distance WOOFER Note You cannot measure the speaker height of the surround speakers and the surround back speakers. Set this value using the "SUR POS." parameter in the SYSTEM menu (page 59). Tip The measurements may not be performed correctly or Auto Calibration cannot be performed when special speakers, such as dipole speakers are used. To cancel Auto Calibration The Auto Calibration function will be canceled when you do the following during the measurement process: - Press ?/1, input buttons or MUTING. - Press SPEAKERS (OFF/A/B/A+B) on the receiver. - Change the volume level. - Press AUTO CAL again. - Connect the headphones. Confirming/saving the measurement results 1 Confirm the measurement result. When the measurement ends, a beep sounds and the measurement result appears on the display. Measurement Display Explanation result When the measurement process completes properly SAVE Proceed to step 2. When the measurement process fails ERROR XXXX See "When error codes appear" (page 37). 2 Press RECEIVER and then press V/v repeatedly to select the item. Then, press . Item RETRY SAVE WARN CHK PHASE DISTANCE LEVEL EXIT Explanation Performs the Auto Calibration again. Saves the measurement results and exits the setting process. Displays warning concerning the measurement results. See "When you select "WARN CHK"" (page 38). Displays the phase of each speaker (in phase/out of phase). See "When you select "PHASE"" (page 38). Displays the measurement result for speaker distance. Displays the measurement result for speaker level. Exits the setting process without saving the measurement results. 36US

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
36
US
Press AUTO CAL.
Measurement starts in 5 seconds and the
display changes as follows:
A. CAL [5]
t
A. CAL [4]
t
A. CAL [3]
t
A. CAL [2]
t
A. CAL [1]
The measurement process will take
approximately 30 seconds to complete.
The table below shows the display when
measurement starts.
Note
You cannot measure the speaker height of the
surround speakers and the surround back speakers.
Set this value using the “SUR POS.” parameter in
the SYSTEM menu (page 59).
Tip
The measurements may not be performed correctly
or Auto Calibration cannot be performed when
special speakers, such as dipole speakers are used.
To cancel Auto Calibration
The Auto Calibration function will be
canceled when you do the following during the
measurement process:
– Press
?
/
1
, input buttons or MUTING.
– Press SPEAKERS (OFF/A/B/A+B) on the
receiver.
– Change the volume level.
– Press AUTO CAL again.
– Connect the headphones.
1
Confirm the measurement
result.
When the measurement ends, a beep
sounds and the measurement result
appears on the display.
2
Press RECEIVER and then
press
V
/
v
repeatedly to select
the item. Then, press
.
Measurement for
Display
Speaker existance
TONE
Speaker gain, distance, frequency
response
T.S.P.
Sub woofer gain and distance
WOOFER
Confirming/saving the
measurement results
Measurement
result
Display
Explanation
When the
measurement
process
completes
properly
SAVE
Proceed to step
2.
When the
measurement
process fails
ERROR
XXXX
See “When
error codes
appear” (page
37).
Item
Explanation
RETRY
Performs the Auto
Calibration again.
SAVE
Saves the measurement
results and exits the setting
process.
WARN CHK
Displays warning
concerning the
measurement results. See
“When you select “WARN
CHK”” (page 38).
PHASE
Displays the phase of each
speaker (in phase/out of
phase). See “When you
select “PHASE”” (page 38).
DISTANCE
Displays the measurement
result for speaker distance.
LEVEL
Displays the measurement
result for speaker level.
EXIT
Exits the setting process
without saving the
measurement results.