Sony DG910 Instructions Manual - Page 40

When a test tone is not output, from the speakers, T. TONE N.

Get Sony DG910 - STR AV Receiver PDF manuals and user guides
UPC - 027242707023
View all Sony DG910 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 40 highlights

2 Press MENU. "1-LEVEL" appears on the display. 3 Press or b to enter the menu. 4 Press V/v repeatedly to select "T. TONE". 5 Press or b to enter the parameter. 6 Press V/v repeatedly to select "T. TONE Y". The test tone is output from each speaker in sequence as follows: Front left t Center t Front right t Surround right t Surround back right* t Surround back left* t Surround left t Sub woofer * You will only hear the test tone from the - surround back left and right speakers when surround back speakers are set to "DUAL". - surround back left speaker when surround back speakers are set to "SINGLE". 7 Adjust the speaker levels and balance using the LEVEL menu so that the level of the test tone sounds the same from each speaker. For details, see "Adjusting the level (LEVEL menu)" (page 50). Tips • To adjust the level of all speakers at the same time, press MASTER VOL +/-. You can also use MASTER VOLUME on the receiver. • The adjusted value are shown on the display during adjustment. 8 Repeat steps 1 to 6 to select "T. TONE N". You can also press any input buttons. The test tone turns off. When a test tone is not output from the speakers • The speaker cords may not be connected securely. • The speaker cords may have the short-circuit problem. Note The test tone does not work when ANALOG DIRECT is selected. 40US

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
40
US
2
Press MENU.
“1-LEVEL” appears on the display.
3
Press
or
b
to enter the
menu.
4
Press
V
/
v
repeatedly to select
“T. TONE”.
5
Press
or
b
to enter the
parameter.
6
Press
V
/
v
repeatedly to select
“T. TONE Y”.
The test tone is output from each speaker
in sequence as follows:
Front left
t
Center
t
Front right
t
Surround right
t
Surround back right*
t
Surround back left*
t
Surround left
t
Sub woofer
* You will only hear the test tone from the
– surround back left and right speakers when
surround back speakers are set to “DUAL”.
– surround back left speaker when surround
back speakers are set to “SINGLE”.
7
Adjust the speaker levels and
balance using the LEVEL menu
so that the level of the test tone
sounds the same from each
speaker.
For details, see “Adjusting the level
(LEVEL menu)” (page 50).
Tips
• To adjust the level of all speakers at the same
time, press MASTER VOL +/–. You can also
use MASTER VOLUME on the receiver.
• The adjusted value are shown on the display
during adjustment.
8
Repeat steps 1 to 6 to select
“T. TONE N”.
You can also press any input buttons.
The test tone turns off.
When a test tone is not output
from the speakers
•
The speaker cords may not be connected
securely.
•
The speaker cords may have the short-circuit
problem.
Note
The test tone does not work when ANALOG
DIRECT is selected.