Sony STR-DA3400ES Operating Instructions (Large File - 15.18 MB) - Page 47

To cancel the measurement, Confirming/saving the, measurement results

Get Sony STR-DA3400ES - 7.1 Channel Es Receiver PDF manuals and user guides View all Sony STR-DA3400ES manuals
Add to My Manuals
Save this manual to your list of manuals

Page 47 highlights

Getting Started 9 Measurement starts. The measurement process will take approximately 30 seconds with a test tone. Wait until the measurement process completes. Confirming/saving the measurement results 1 Confirm the measurement result. When the measurement ends, a beep sounds and the measurement result appears on the TV screen. Tips • Operations other than turning the receiver on or off are deactivated during the measurement. • In the following situations, the measurements have not been performed correctly or Auto Calibration cannot be performed. - when connecting special speakers, such as dipole speakers. - when using the zone 2 function in zone 2. To cancel the measurement The measurement will be canceled when you do the following: - Press ?/1, input buttons or MUTING. - Press SPEAKERS (OFF/A/B/A+B) on the receiver. - Change the volume level. - Connect the headphones. - Press GUI MODE. Note When the speaker(s) is (are) out of the phase, "Out Phase" is displayed on the TV screen. The "+" and "-" terminals of the speaker may be connected the other way around. However, depending on the speakers, "Out Phase" appears on the TV screen even though the speakers are connected properly. This is because of the speakers' specifications. In this case, you can continue to use the receiver. Tip The displayed unit of distance is feet. You can change the unit of distance to meters in "Distance Unit" in the Speaker settings menu. 2 Press to select "Next". When "Save auto calibration (auto speaker setup) results?" appears on the TV screen, you can select whether to confirm the warning ("Yes") or not ("No"). Follow the instructions of the TV screen when you select "Yes". For details on warning and error codes, see "Message list after Auto Calibration measurement" (page 49). Tip Press on the remote when "Please Press ENTER." appears on the TV screen. continued 47US

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
47
US
Getting Started
9
Measurement starts.
The measurement process will take
approximately 30 seconds with a test
tone. Wait until the measurement process
completes.
Tips
• Operations other than turning the receiver on or off
are deactivated during the measurement.
• In the following situations, the measurements have
not been performed correctly or Auto Calibration
cannot be performed.
–
when connecting special speakers, such as
dipole speakers.
–
when using the zone 2 function in zone 2.
To cancel the measurement
The measurement will be canceled when you
do the following:
– Press
?
/
1
, input buttons or MUTING.
– Press SPEAKERS (OFF/A/B/A+B) on the
receiver.
– Change the volume level.
– Connect the headphones.
– Press GUI MODE.
1
Confirm the measurement
result.
When the measurement ends, a beep
sounds and the measurement result
appears on the TV screen.
Note
When the speaker(s) is (are) out of the phase,
“Out Phase” is displayed on the TV screen.
The “+” and “–” terminals of the speaker may
be connected the other way around. However,
depending on the speakers, “Out Phase”
appears on the TV screen even though the
speakers are connected properly. This is
because of the speakers’ specifications. In this
case, you can continue to use the receiver.
Tip
The displayed unit of distance is feet. You can
change the unit of distance to meters in
“Distance Unit” in the Speaker settings menu.
2
Press
to select “Next”.
When “Save auto calibration (auto
speaker setup) results?” appears on the
TV screen, you can select whether to
confirm the warning (“Yes”) or not
(“No”).
Follow the instructions of the TV screen
when you select “Yes”.
For details on warning and error codes,
see “Message list after Auto Calibration
measurement” (page 49).
Tip
Press
on the remote when “Please Press
ENTER.” appears on the TV screen.
Confirming/saving the
measurement results
continued