Sony STR-DA3400ES Operating Instructions (Large File - 15.18 MB) - Page 49

Message list after Auto Calibration measurement, continued

Get Sony STR-DA3400ES - 7.1 Channel Es Receiver PDF manuals and user guides View all Sony STR-DA3400ES manuals
Add to My Manuals
Save this manual to your list of manuals

Page 49 highlights

Getting Started Message list after Auto Calibration measurement Message appears in GUI menu [Display window] Explanation Error Code: 31 SPEAKERS (OFF/A/B/A+B) is set to off. Set it to others and perform the measurement [E-xxx: 31]* again. Error Code: 32 None of the speakers were detected. Make sure that the optimizer microphone is connected [E-xxx: 32]* properly and perform the measurement again. If the optimizer microphone is connected properly but the error code appears, the optimizer microphone cable may be damaged or improperly connected. Error Code: 33 • None of the front speakers are connected or only one front speaker is connected. [E-xxx: 33]* • The optimizer microphone is not connected. • Either the left or right surround speakers is not connected. • Surround back speakers are connected even though surround speakers are not connected. Connect the surround speaker(s) to the SURROUND terminals. • The surround back speaker is connected only to the SPEAKERS SURROUND BACK R terminals. When you connect only one surround back speaker, connect it to the SPEAKERS SURROUND BACK L terminals. Warning The measurement has completed. However, the noise level is high. You may be able to Code: 40 perform the measurement properly if you try it again, even though the measurement cannot [W-xxx: 40]* be performed in all environments. Try to perform the measurement in a quiet environment. Warning The input from the microphone is too loud. Code: 41 • The distance between the speaker and the microphone may be too close with each other. [W-xxx: 41]* Retry the measurement after setting them further apart from each other. Warning • The volume may be too loud when you use the receiver as a pre-amplifier. Code: 42 [W-xxx: 42]* Warning The distance and position of a subwoofer cannot be detected. This may be caused by noise. Code: 43 Try to perform the measurement in a quiet environment. [W-xxx: 43]* NO WARNING There is no warning information. * xxx represent a speaker channel. F Front FL Front Left FR Front Right CNT Center SL Surround Left SR Surround Right SB Surround Back SBL Surround Back Left SBR Surround Back Right SW Subwoofer •Error Code: 31, 32, 33 1 Press B/b to select "Retry", then press . 2 Press to select "Start". 3 Follow the instructions from step 7 of "Performing Auto Calibration". continued 49US

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
49
US
Getting Started
*
xxx
represent a speaker channel.
F
Front
FL
Front Left
FR
Front Right
CNT
Center
SL
Surround Left
SR
Surround Right
SB
Surround Back
SBL
Surround Back Left
SBR
Surround Back Right
SW
Subwoofer
•Error Code: 31, 32, 33
1
Press
B
/
b
to select “Retry”, then press
.
2
Press
to select “Start”.
3
Follow the instructions from step 7 of
“Performing Auto Calibration”.
Message list after Auto Calibration measurement
Message
appears in
GUI menu
[Display
window]
Explanation
Error Code: 31
[E
-
xxx
:
31]*
SPEAKERS (OFF/A/B/A+B) is set to off. Set it to others and perform the measurement
again.
Error Code: 32
[E
-
xxx
:
32]*
None of the speakers were detected. Make sure that the optimizer microphone is connected
properly and perform the measurement again.
If the optimizer microphone is connected properly but the error code appears, the optimizer
microphone cable may be damaged or improperly connected.
Error Code: 33
[E
-
xxx
:
33]*
•
None of the front speakers are connected or only one front speaker is connected.
•
The optimizer microphone is not connected.
•
Either the left or right surround speakers is not connected.
•
Surround back speakers are connected even though surround speakers are not connected.
Connect the surround speaker(s) to the SURROUND terminals.
•
The surround back speaker is connected only to the SPEAKERS SURROUND BACK R
terminals. When you connect only one surround back speaker, connect it to the SPEAKERS
SURROUND BACK L terminals.
Warning
Code: 40
[W
-
xxx
:
40]*
The measurement has completed. However, the noise level is high. You may be able to
perform the measurement properly if you try it again, even though the measurement cannot
be performed in all environments. Try to perform the measurement in a quiet environment.
Warning
Code: 41
[W
-
xxx
:
41]*
Warning
Code: 42
[W
-
xxx
:
42]*
The input from the microphone is too loud.
•
The distance between the speaker and the microphone may be too close with each other.
Retry the measurement after setting them further apart from each other.
•
The volume may be too loud when you use the receiver as a pre-amplifier.
Warning
Code: 43
[W
-
xxx
:
43]*
The distance and position of a subwoofer cannot be detected. This may be caused by noise.
Try to perform the measurement in a quiet environment.
NO WARNING
There is no warning information.
continued