TP-Link TL-R480T User Guide

TP-Link TL-R480T Manual

Get TP-Link TL-R480T PDF manuals and user guides
UPC - 696726480020
View all TP-Link TL-R480T manuals
Add to My Manuals
Save this manual to your list of manuals

TP-Link TL-R480T manual content summary:

  • TP-Link TL-R480T | User Guide - Page 1
    TL-R480T SMB Broadband Router Rev: 1.1.2 1910010056
  • TP-Link TL-R480T | User Guide - Page 2
    COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced
  • TP-Link TL-R480T | User Guide - Page 3
    energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
  • TP-Link TL-R480T | User Guide - Page 4
    contents The following contents should be found in your box: ¾ One TL-R480T SMB Broadband Router ¾ One power cord for TL-R480T SMB Broadband Router ¾ One Resource CD for TL-R480T SMB Broadband Router, including: • This Guide • Other Helpful Information ¾ Mounting kits for installing in a standard 19
  • TP-Link TL-R480T | User Guide - Page 5
    the Router 4 Chapter 3. Quick Installation Guide 5 3.1 Configure PC ...5 3.2 Login ...8 Chapter 4. Configuring the Router 11 4.1 Status...11 4.2 Quick Setup ...12 4.3 Network...13 4.3.1 LAN...13 4.3.2 WAN ...14 4.3.3 Network service detection 25 4.3.4 MAC Clone ...25 4.3.5 WAN Port Parameter
  • TP-Link TL-R480T | User Guide - Page 6
    ...60 4.13.2 Firmware...61 4.13.3 Factory Defaults ...62 4.13.4 Backup and Restore...62 4.13.5 Reboot ...64 4.13.6 Password...65 4.13.7 System Log ...65 4.13.8 Remote Management...66 4.13.9 Statistics ...67 4.13.10 WAN Speed Detect ...68 4.13.11 IP NAT Table...70 4.13.12 NAT Source Port Settings 70
  • TP-Link TL-R480T | User Guide - Page 7
    TL-R480T SMB Broadband Router is easy-to-manage. Quick Setup is supported and friendly help messages are provided for every step. So you can configure it quickly and share Internet access, files and fun comfortably. 1.2 Features ¾ Complies with IEEE 802.3, 802.3u standards ¾ 4 LAN ports, 1 WAN port
  • TP-Link TL-R480T | User Guide - Page 8
    TL-R480T SMB Broadband Router User Guide ¾ Supports firmware upgrade ¾ Supports Remote and Web management 1.3 Conventions Parameters provided in the pictures are just references for setting up the product, which may differ from the actual situation. You can set the
  • TP-Link TL-R480T | User Guide - Page 9
    TL-R480T SMB Broadband Router User Guide There are two ways to reset the router: Method one: Use the Factory Defaults function on System Tools -> Factory Defaults page in the router's Web-based Utility. Method two: Use the Factory Default Reset button: Press the Reset button for five seconds and
  • TP-Link TL-R480T | User Guide - Page 10
    lightning. TL-R480T SMB Broadband Router User Guide 2.4 Connecting the Router Before you install the router, you should connect your PC to the Internet through your broadband service successfully. If there is any problem, please contact with your ISP for help. After that, please install the router
  • TP-Link TL-R480T | User Guide - Page 11
    TL-R480T SMB Broadband Router User Guide Chapter 3. Quick Installation Guide After connecting the TL-R480T router into your network, you should configure it. This chapter describes how to configure the basic functions of your TL-R480T SMB Broadband Router. These procedures only take you a few
  • TP-Link TL-R480T | User Guide - Page 12
    TL-R480T SMB Broadband Router User Guide Figure 3-2 Step 3: In the next screen, select General tab, highlight Internet Protocol (TCP/IP), and then click the Properties button. Figure 3-3 6
  • TP-Link TL-R480T | User Guide - Page 13
    TL-R480T SMB Broadband Router User Guide Step 4: Configure the IP address as shown in Figure 3-4. After that, click OK. Figure 3-4 ) Note: You can configure the PC to get an IP address manually, select "Obtain an IP address automatically" and "Obtain DNS server address automatically" in the screen
  • TP-Link TL-R480T | User Guide - Page 14
    Is the connection between your PC and the Router correct? The LEDs of LAN port which you link to the device and the LEDs on your PC's adapter should be lit. Is the TCP/IP configuration for your PC correct? If the Router's IP address is 192.168.1.1, your PC's IP address must be within the range of
  • TP-Link TL-R480T | User Guide - Page 15
    TL-R480T SMB Broadband Router User Guide ) Note: Figure 3-7 If the above screen (Figure 3-7) does not prompt, it means that your web-browser may be set to a proxy. Choose Tools menu→Internet Options→Connections→LAN the Quick Setup tab on the left of the main menu and the "Quick Setup" screen will
  • TP-Link TL-R480T | User Guide - Page 16
    TL-R480T SMB Broadband Router User Guide ) Note: The router supports three popular ways to connect to Internet. Please select one compatible with your ISP, if you are given another way not listed here, refer to Network→ WAN for detailed list. Step 3: If you choose PPPoE, you will see the screen as
  • TP-Link TL-R480T | User Guide - Page 17
    TL-R480T SMB Broadband Router User Guide Chapter 4. Configuring the Router This User Guide recommends using the "Quick Installation Guide" for first-time installation. For advanced users, if you want to know more about this device and make use of its functions adequately, you need to read this
  • TP-Link TL-R480T | User Guide - Page 18
    TL-R480T SMB Broadband Router User Guide Figure 4-1 ¾ LAN - This field displays the current information for the LAN, including the "MAC address", "IP address" and "Subnet Mask". ¾ WAN - This field displays the parameters applied to the WAN ports of the router, including "MAC address", "IP address",
  • TP-Link TL-R480T | User Guide - Page 19
    Network TL-R480T SMB Broadband Router User Guide Choose menu "Network", the next submenus are shown below: Figure 4-2 Click any of them, and you will be able to configure the corresponding function. The detailed explanations for each submenu are provided below. 4.3.1 LAN Choose menu "Network→LAN
  • TP-Link TL-R480T | User Guide - Page 20
    TL-R480T SMB Broadband Router User Guide 4.3.2 WAN Choose menu "Network→WAN", you can configure the IP parameters of the WAN on the screen below. The Router provides six connection types for WAN to connect to the Internet, they are "Dynamic IP", "Static IP" , "PPPoE", "BigPondCable" , "L2TP" and "
  • TP-Link TL-R480T | User Guide - Page 21
    TL-R480T SMB Broadband Router User Guide enter the LAN IP addresses in the field, then the WAN port will only transmit the traffic whose destination IP address are contained in the field. ¾ MTU Size - The normal MTU (Maximum Transmission Unit) value for most Ethernet networks is 1500 Bytes. For some
  • TP-Link TL-R480T | User Guide - Page 22
    TL-R480T SMB Broadband Router User Guide Figure 4-5 ¾ IP Address - Enter the IP address in dotted-decimal notation provided by your ISP. ¾ Subnet Mask - Enter the subnet Mask in dotted-decimal notation provided by your ISP, usually is 255.255.255.0. ¾ Default Gateway - Enter the gateway IP address
  • TP-Link TL-R480T | User Guide - Page 23
    correct information. TL-R480T SMB Broadband Router User Guide Figure 4-6 ¾ User Name/Password - Enter the User Name and Password provided by your ISP. These fields are case-sensitive. ¾ Connect on Demand - You can configure the router to disconnect your Internet connection after a specified period
  • TP-Link TL-R480T | User Guide - Page 24
    TL-R480T SMB Broadband Router User Guide Manually - You can configure the router to make it connect or disconnect manually. After a specified period of inactivity (Max Idle Time), the router to have the Internet connecting last unless a new link is requested. 2) Sometimes the connection cannot be
  • TP-Link TL-R480T | User Guide - Page 25
    TL-R480T SMB Broadband Router User Guide Figure 4-7 ¾ MTU Size- The default MTU size is 1492 bytes, which is usually fine. For some ISPs, you need modify the MTU. This should not be done unless you are sure it is necessary for your ISP. ¾ Service Name/AC Name - The service name and AC (Access
  • TP-Link TL-R480T | User Guide - Page 26
    TL-R480T SMB Broadband Router User Guide 4. BigPondCable If your ISP provides BigPond Cable (or Heart Beat Signal) connection, please select BigPond Cable option. Figure 4-8 ¾ User Name/Password - Enter the User Name and Password on Demand - You can configure the router to disconnect your Internet
  • TP-Link TL-R480T | User Guide - Page 27
    TL-R480T SMB Broadband Router User Guide terminates. ¾ Connect Automatically - Connect automatically after the router is disconnected. To use this option, click the radio button. ¾ Connect Manually - You can configure the router to make it connect or disconnect manually unless a new link requested. )
  • TP-Link TL-R480T | User Guide - Page 28
    TL-R480T SMB Broadband Router User Guide Figure 4-9 ¾ User Name/Password - Enter the User Name and Password provided by your ISP. These fields are case-sensitive. ¾ Connect on Demand - You can configure the router to disconnect your Internet connection after a specified period of the Internet
  • TP-Link TL-R480T | User Guide - Page 29
    TL-R480T SMB Broadband Router User Guide ¾ Connect Automatically - Connect automatically after the router is disconnected. To use this option, click the radio button. ¾ Connect Manually - You can configure the router to make it connect or disconnect manually last unless a new link requested. ) Note:
  • TP-Link TL-R480T | User Guide - Page 30
    TL-R480T SMB Broadband Router User Guide Figure 4-10 ¾ User Name/Password - Enter the User Name and Password provided by your ISP. These fields are case-sensitive. ¾ Connect on Demand - You can configure the router to disconnect your Internet connection after a specified period of the Internet
  • TP-Link TL-R480T | User Guide - Page 31
    TL-R480T SMB Broadband Router User Guide ¾ Connect Manually - You can configure the router to make it connect or disconnect manually. After a specified period of inactivity (Max Idle Time), the router will disconnect your Internet connection, and not be able to re-establish your connection
  • TP-Link TL-R480T | User Guide - Page 32
    TL-R480T SMB Broadband Router User Guide Figure 4-12 ¾ WAN MAC Address - This field displays the current MAC address of the WAN port, which is used for the WAN port. If your ISP requires that you register the MAC address, please enter the correct MAC address into this field. The format for the MAC
  • TP-Link TL-R480T | User Guide - Page 33
    TL-R480T SMB Broadband Router User Guide Figure 4-13 ¾ WAN Index - This shows the Router's WAN ports. ¾ Port Status - This shows the ports' current status: Enabled or Disabled, the default status is Enabled. ¾ Flow Control - This displays whether the Flow Control is Enabled, "Enabled" means the
  • TP-Link TL-R480T | User Guide - Page 34
    TL-R480T SMB Broadband Router User Guide explanations for each submenu are provided below. 4.4.1 DHCP Settings Choose menu "DHCP→DHCP Settings", you can configure the DHCP in the next screen (shown in Figure 4-15). The router is set up by default as a DHCP (Dynamic Host Configuration Protocol)
  • TP-Link TL-R480T | User Guide - Page 35
    TL-R480T SMB Broadband Router User Guide ) Note: To use the DHCP server function of the router, you must configure all computers on the LAN as "Obtain an IP Address automatically" mode. This function will take effect until the router reboots. 4.4.2 DHCP Clients List Choose menu "DHCP→DHCP Clients
  • TP-Link TL-R480T | User Guide - Page 36
    TL-R480T SMB Broadband Router User Guide reserve IP address. ¾ Assigned IP Address - This field displays the IP address of the router more than one reserved IP, please go to step 1 to continue. 5) The function won't take effect until the router reboots. Other configurations for the entries as shown
  • TP-Link TL-R480T | User Guide - Page 37
    TL-R480T SMB Broadband Router User Guide Figure 4-19 Click any of them, and you will be able to configure the corresponding function. The detailed explanations for each submenu are provided below. 4.5.1 Virtual Servers Choose menu "Forwarding→Virtual Servers", you can view and add virtual servers in
  • TP-Link TL-R480T | User Guide - Page 38
    TL-R480T SMB Broadband Router User Guide contain the service that you want, please configure the Service Port, IP Address and Protocol manually. Figure 4-21 Step 3: After that, select Enable to make the entry take effect. Step 4: Click Save button to save the configuration. ) Note: 6) If you want to
  • TP-Link TL-R480T | User Guide - Page 39
    TL-R480T SMB Broadband Router User Guide for some of these applications that can work with an NAT router. Figure 4-22 ¾ Trigger Port - This displays the port for outgoing traffic. An outgoing connection using this port will "Trigger" this rule. ¾ Trigger Protocol - This displays the protocol used
  • TP-Link TL-R480T | User Guide - Page 40
    options manually. TL-R480T SMB Broadband Router User Guide Figure 4-23 Step 3: After that, select Enabled to make the entry take effect. Step 4: Click Save button to save the configuration. ) Note: 1) If you want to add more than one reserved IP, please go to step 1 to continue. 2) When the
  • TP-Link TL-R480T | User Guide - Page 41
    TL-R480T SMB Broadband Router User Guide Figure 4-24 To assign a computer or server to be a DMZ server: Step 1: Click the Enable radio button Step 2: Enter the local host IP address in the DMZ Host IP service application on the LAN. Figure 4-25 ¾ Current UPnP Status - If you want to use the Router's
  • TP-Link TL-R480T | User Guide - Page 42
    TL-R480T SMB Broadband Router User Guide ¾ Protocol - This displays the protocol for the application. ¾ Internal Port - This displays the Internal port, which the router opened for local host. ¾ IP Address - The UPnP device that is currently accessing the router. ¾ Status - This displays the status.
  • TP-Link TL-R480T | User Guide - Page 43
    TL-R480T SMB Broadband Router User Guide Figure 4-27 ¾ Enable Firewall - Enable the general firewall switch or not. ¾ Enable IP Address Filtering - Enable the IP Address Filtering or not. There are two default filtering rules, please select the rule for your need. ¾ Enable Domain Filtering - Enable
  • TP-Link TL-R480T | User Guide - Page 44
    TL-R480T SMB Broadband Router User Guide Figure 4-28 ¾ Effective Time - This is the time or the range of time for the entry to take effect. For example, 1800 - 2200, it means that the entry will take effect from 18:00 to 22:00. ¾ LAN IP - This is the LAN IP address or the range of LAN IP addresses
  • TP-Link TL-R480T | User Guide - Page 45
    TL-R480T SMB Broadband Router User Guide Step 2: Click Add New.../Modify shown in Figure 4-28, you will see a new screen shown in Figure 4-29. Step 3: Enter the "Effective time" that the rule will take effect as shown in Figure 4-29. Step 4: Enter the "LAN IP Address", "LAN Port", "WAN IP Address"
  • TP-Link TL-R480T | User Guide - Page 46
    TL-R480T SMB Broadband Router User Guide 4.6.3 Domain Filtering Choose menu "Security→Domain Filtering", you can configure the Domain Domain Filtering entry: For example: if you want to block the PCs on your LAN from accessing websites www.xxyy.com.cn, www.aabbcc.com and websites with end of
  • TP-Link TL-R480T | User Guide - Page 47
    TL-R480T SMB Broadband Router User Guide Figure 4-32 Step 5: Finally, click Save to make the rule take effect. Step 6: Go to Step 2 to complete the other rules continually. After you finish the configurations, you will see the rules in the table below: Figure 4-33 ) Note: Before adding an IP Address
  • TP-Link TL-R480T | User Guide - Page 48
    TL-R480T SMB Broadband Router User Guide Figure 4-34 ¾ MAC Address - .This is the PC access the Internet, you can configure as follows. Step 1: Enable the "Firewall" and "MAC Address Filtering" on the Firewall screen (show in Figure 4-27). And then specify the Default MAC Address Filtering Rule "Deny
  • TP-Link TL-R480T | User Guide - Page 49
    TL-R480T SMB Broadband Router User Guide Figure 4-35 Step 4: Finally, click Save to make the rule take effect. Step 5: Go to Step 2 to complete the other rules continually. After you finish the configurations, you will see the rules in the table below: Figure 4-36 ) Note: Before adding a MAC Address
  • TP-Link TL-R480T | User Guide - Page 50
    TL-R480T SMB Broadband Router User Guide Figure 4-37 ¾ Region - This option used to select the specifically area from which the packets will be monitored by the next settings. ¾ Scan Attack Defence • IP Scan: During the specific time, if a computer (identified by a particular source IP address)
  • TP-Link TL-R480T | User Guide - Page 51
    TL-R480T SMB Broadband Router User Guide • Port Scan - During the specific time, if a computer (identified by a particular source IP address) transmits TCP SYN packets to another computer's (identified by a destination IP address) ten different ports, then the source IP address will be deemed to
  • TP-Link TL-R480T | User Guide - Page 52
    TL-R480T SMB Broadband Router User Guide ACK is considered as abnormal. And the Router will start up the blocking function immediately. • Unknow Protocol - In IP head the protocol type field, 135 and the value bigger than 135 is reserved and undefined. Because the protocols are undefined, we can not
  • TP-Link TL-R480T | User Guide - Page 53
    TL-R480T SMB Broadband Router User Guide Figure 4-38 ¾ Destination IP Address - The "Destination IP Address" is the address of the network or host that you want to assign to a static route. ¾ Subnet Mask - The "Subnet Mask" determines which portion of an IP IP Address, Subnet Mask and Default
  • TP-Link TL-R480T | User Guide - Page 54
    TL-R480T SMB Broadband Router User Guide Click the Delete button to delete the entry. Click session limit. Only after choose "Enable", the configuration will take effect. ¾ LAN IP address: The controlled computer's IP address. You can input an range of IP address, for example: 192.168.1.20 -192.168
  • TP-Link TL-R480T | User Guide - Page 55
    TL-R480T SMB Broadband Router User Guide Figure 4-42. Step 2: Enter the appropriate LAN IP Address, Max Session and then select the update the information. 4.9 QoS Choose menu "QoS", you can see the submenus under the main menu: Figure 4-44 Click any of them, and you will be able to configure
  • TP-Link TL-R480T | User Guide - Page 56
    TL-R480T SMB Broadband Router User Guide 4.9.1 QoS Settings Choose menu "QoS→QoS Settings", you can configure the Upload Bandwidth and Download Bandwidth in the next screen, their value you configure should be less than 1000000Kbps. Figure 4-45 4.9.2 QoS Rules List Choose menu "QoS→QoS Rules List",
  • TP-Link TL-R480T | User Guide - Page 57
    TL-R480T SMB Broadband Router User Guide Step 3: Click the Save button. Figure 4-47 4.10 IP & MAC Binding Choose menu "IP & MAC Binding", you can see the submenus under the main menu: Binding Setting, ARP List. Figure 4-48 Click any of them, and you will be able to configure the corresponding
  • TP-Link TL-R480T | User Guide - Page 58
    TL-R480T SMB Broadband Router User Guide Figure 4-49 ¾ MAC Address - This field displays the MAC address of the controlled computer in the LAN. ¾ IP Address - This field displays the assigned IP address of the controlled computer in the LAN. ¾ Bind - Select Whether enable the arp binding or not.
  • TP-Link TL-R480T | User Guide - Page 59
    TL-R480T SMB Broadband Router User Guide Figure 4-51 Step 3: Click Find button, then you will see the entry with the specific MAC address or IP address. Step 4: Click Back to return the previous screen. ) Note: You can click "to page" to edit the entry in the corresponding screen. Other
  • TP-Link TL-R480T | User Guide - Page 60
    TL-R480T SMB Broadband Router User Guide Click Load to load the specific item to the IP & MAC Binding list (shown in Figure 4-49). Click Delete to load the specific item to the IP & MAC Binding list. Click the Bind All button to bind all the current items, available after enable. Click the Load All
  • TP-Link TL-R480T | User Guide - Page 61
    TL-R480T SMB Broadband Router User Guide Step 1: Type the "User Name" and "Password" for your DDNS account. Step 2: Enter the domain name that your dynamic DNS service provider offers. Step 3: Enable DDNS, and click Save to save the current configuration. Click Login to login the DDNS service. Click
  • TP-Link TL-R480T | User Guide - Page 62
    TL-R480T SMB Broadband Router User Guide Figure 4-55 To set up for Comexe DDNS, follow these instructions: Step 1: Enter the domain name your dynamic DNS service provider offer. Step 2: Type the "User Name" and "Password" for your DDNS account. Step 3: Enable DDNS, and click Save to save the current
  • TP-Link TL-R480T | User Guide - Page 63
    TL-R480T SMB Broadband Router User Guide Figure 4-56 Click any of them, and you will be able to configure the corresponding function. The detailed explanations for each submenu are provided below. 4.12.1 Port Statistics Choose menu "Switch Setting→Port statistics", you can view the statistics
  • TP-Link TL-R480T | User Guide - Page 64
    TL-R480T SMB Broadband Router User Guide Figure 4-58 ¾ Mirror Config - There are three Mirror modes: Disable, Output mirror, Input mirror. The Output/Input mirror is related to the Router. ¾ Port Mirror - This is the port linked to the mirror computer. ¾ Mirrored Ports List - The option used to
  • TP-Link TL-R480T | User Guide - Page 65
    TL-R480T SMB Broadband Router User Guide Figure 4-60 4.12.5 Port Status Choose menu "Switch Setting→Port Status", you can view the status of the LAN port in the next screen (shown in Figure 4-61). Figure 4-61 4.12.6 Port VLAN Choose menu "Switch Setting→Port VLAN", you can view and configure the
  • TP-Link TL-R480T | User Guide - Page 66
    TL-R480T SMB Broadband Router User Guide ¾ Port - You can select them as the members of VLAN. ¾ Enable - This used to enable the corresponding VLAN configuration. ¾ Clean - Click this button, you can make all the entries Disabled. ¾ Save - Click this button, the Router will make a new VLAN table
  • TP-Link TL-R480T | User Guide - Page 67
    of the upgrade file must accord with the Router's current hardware version. To upgrade the router's firmware, follow these instructions below: Step 1: Download a more recent firmware upgrade file from the TP-LINK website (www.tp-link.com). Step 2: Type the path and file name of the update file into
  • TP-Link TL-R480T | User Guide - Page 68
    R480T SMB Broadband Router User Guide button to locate the update file. Step 3: Click the Upgrade button. ) Note: 1) New firmware versions are posted at www.tp-link.com and can be downloaded for free. If the router is not experiencing difficulties, there is no need to download a more recent firmware
  • TP-Link TL-R480T | User Guide - Page 69
    TL-R480T SMB Broadband Router User Guide Figure 4-67 To back up the Router's current settings: Step 1: Click the Backup button (shown in Figure 4-67), click Save button in the next screen (shown in Figure 4-68) to proceed. Figure 4-
  • TP-Link TL-R480T | User Guide - Page 70
    TL-R480T SMB Broadband Router User Guide Figure 4-69 To restore the Router's settings: Step 1: Click the Browse button to locate the update file for the device, or enter the exact path to the Setting file in the text box. Step 2: Click the Restore button to complete. 4.13.5
  • TP-Link TL-R480T | User Guide - Page 71
    TL-R480T SMB Broadband Router User Guide 4) Static address assignment of DHCP server. 5) Web Service Port of the router. 6) Upgrade the firmware of the router (system will reboot automatically). 7) Restore the router's settings to factory default (system will reboot automatically). 4.13.6 Password
  • TP-Link TL-R480T | User Guide - Page 72
    configure the Remote Management function on this screen (shown in Figure 4-73). This feature allows you to manage your Router from a remote location via the Internet. Figure 4-73 ¾ Web Management Port - Web browser access normally uses the standard HTTP service port 80. This router's default remote
  • TP-Link TL-R480T | User Guide - Page 73
    TL-R480T SMB Broadband Router User Guide 1) To access the router, you will type your router's WAN IP address into your browser's address (in IE) or Location (in Navigator) box, followed by a colon and the custom port number. For example, if your Router's WAN address is 202.96.12.8, and the port
  • TP-Link TL-R480T | User Guide - Page 74
    TL-R480T SMB Broadband Router User Guide Total Packets Bytes The total amount of packets received and transmitted by the router The total amount of bytes received and transmitted by the router Packets The total amount of packets received and transmitted in the last "Packets Statistic interval"
  • TP-Link TL-R480T | User Guide - Page 75
    TL-R480T SMB Broadband Router User Guide Figure 4-75 ¾ Destination IP - the IP address which datagrams are sent to, such as- 202.96.134.188. ¾ ID - The number of ICMP datagrames to be sent. ¾ Source Port - The port where datagrams are sent to, such as- 5000 ¾ Destination Port - The datagrams'
  • TP-Link TL-R480T | User Guide - Page 76
    TL-R480T SMB Broadband Router User Guide considered to be a domain name, DNS datagram will be sent, at this time, no matter what the destination port is, the destination port in the sent datagram is always 53. If not, it will be sent as a whole UDP datagram. ¾ Detect Result - The interval between
  • TP-Link TL-R480T | User Guide - Page 77
    TL-R480T SMB Broadband Router User Guide Appendix A: Specifications General IEEE 802.3, 802.3u Standards and Protocols TCP/IP, PPPoE, DHCP, ICMP, NAT, SNTP,HTTP,DNS Safety & Emission Ports FCC、CE One 10/100M Auto-Negotiation WAN RJ45 port. Four 10/100/1000M Auto-Negotiation LAN RJ45 ports (Auto
  • TP-Link TL-R480T | User Guide - Page 78
    TL-R480T SMB Broadband Router User Guide Appendix B: FAQ 1. How do I configure the router to access Internet by ADSL users? Step 1: First, configure the ADSL modem in RFC1483 bridge model. Step 2: Connect the Ethernet cable from your ADSL modem to the WAN port on the router. The telephone cord plugs
  • TP-Link TL-R480T | User Guide - Page 79
    TL-R480T SMB Broadband Router User Guide 2. How do I configure the router to access Internet by Ethernet users? Step 1: Login to the router, click the menu Network→WAN on the left of your browser, On the WAN screen, select "Dynamic IP" for "WAN Connection Type", and finish it by clicking Save. Step
  • TP-Link TL-R480T | User Guide - Page 80
    TL-R480T SMB Broadband Router User Guide Figure B-4 ) Note: Your opposite side should call your WAN IP, which is displayed on the "Status" page. Method two: Use DMZ Host Login to the router, click the menu Forwarding→DMZ. On the DMZ screen, select "Enable", and enter your IP address into the "DMZ
  • TP-Link TL-R480T | User Guide - Page 81
    TL-R480T SMB Broadband Router User Guide Figure B-6 ) Note: If the above configuration takes effect, you should login the Router by entrying http://192.168.1.1:88 (the router's LAN IP address: Web Management Port) in the address field of the web browser. Step 2: To add a WEB Server: Login to the
  • TP-Link TL-R480T | User Guide - Page 82
    TL-R480T SMB Broadband Router User Guide Appendix C: Glossary ¾ DDNS (Dynamic Domain Name System) - The capability of assigning a fixed host and domain name to a dynamic Internet IP address. ¾ DHCP (Dynamic Host Configuration Protocol) - A protocol that automatically configure the TCP/IP parameters
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
TL-R480T
SMB Broadband Router
Rev: 1.1.2
1910010056