Weider 9400 Instruction Manual - Page 12
from the Small Pulley Plates 31.
View all Weider 9400 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 12 highlights
19. Route the Swivel High Cable (74) through the Swivel Upright (5) and over a 115mm Pulley (119). Attach 19 the Pulley inside the Upright with an M10 x 65mm Bolt (18), two M10 Washers (91), two 12mm Spacers (89), and an M10 Nylon Locknut (87). Attach an M10 x 65mm Bolt (18), two M10 Washers (91), and an M10 Nylon Locknut (87) to the Swivel Upright (5). 5 91 87 91 87 89 91 18 18 91 89 74 119 20. Remove the preattached 90mm Pulleys (78) 20 from the Small Pulley Plates (31). Wrap the Swivel High Cable (74) under a 90mm Pulley (78). Attach the Pulley and a pair of Pulley Covers (68) to the second set of holes from the top of the Small Pulley Plates (31) with an M10 x 50mm Bolt (100) and an M10 Nylon Locknut (87). Make sure the small tabs on the Pulley Covers are on the top. 21. Wrap the Swivel High Cable (74) over a 115mm 21 Pulley (119). Attach the Pulley inside of the indicat- ed bracket on the Top Frame (6) with M10 x 45mm Bolt (93) and an M10 Nylon Locknut (87). Small 74 Tab 87 100 68 78 31 68 31 6 93 87 22. Lift the Weight Tube (43) and the Top Weight (45) 22 closest to the Swivel Upright (5). Make sure that the small pin on the Weight Tube is inside of the groove under the Top Weight. Insert a Weight Pin (50) into the stack of Weights (44). Place a 50mm Washer (1) on top of the Weight Tube (43). Tighten an M12 Nut (118) halfway onto the end of the Swivel High Cable (74). Screw the end of the Cable two full turns into the Weight Tube. Then, tighten the M12 Nut against the Washer. 23. Locate the Swivel Cable (17), which is 3005mm 23 long and has an eyelet on each end. Attach the Cable inside the Top Frame (6) with an M10 x 65mm Bolt (18), two M10 Washers (91), and an M10 Nylon Locknut (87). 119 74 74 5 118 50 45 1 43 44 18 91 87 17 6 12 44. Wrap the Swivel Low Cable (72) over a 90mm Pulley (78). Attach the Pulley and a pair of Pulley Covers (68) to the Offset Double "U"-bracket (61) with an M10 x 50mm Bolt (100) and an M10 Nylon Locknut (87). Make sure the small tabs on the Pulley Covers are on the bottom. 45. Wrap the Swivel Low Cable (72) under a 90mm Pulley (78). Attach the Pulley and a pair of Pulley Covers (68) to the indicated bracket on the Long Base (101) with an M10 x 50mm Bolt (100) and an M10 Nylon Locknut (87). Make sure the large tabs on the Pulley Covers are oriented as indicated. 46. Route the Swivel Low Cable (72) under the indicated stack of Weights (44). Wrap the Swivel Low Cable (72) under a 90mm Pulley (78). Attach the Pulley and a pair of Pulley Covers (68) to the indicated bracket on the Long Base (101) with an M10 x 50mm Bolt (100) and an M10 Nylon Locknut (87). Make sure the small tabs on the Pulley Covers are oriented as indicated. 47. Wrap the Swivel Low Cable (72) over a 90mm Pulley (78). Attach the Pulley and a pair of Pulley Covers (68) between the indicated holes in the Pulley Plates (63) with an M10 x 50mm Bolt (100) and an M10 Nylon Locknut (87). Make sure the small tabs on the Pulley Covers are on the bottom. 48. Wrap the Swivel Low Cable (72) under a 90mm Pulley (78). Attach the Pulley and a pair of Pulley Covers (68) to the indicated bracket on the Short Base (2) with an M10 x 50mm Bolt (100) and an M10 Nylon Locknut (87). Make sure the small tabs on the Pulley Covers are on top. 44 61 100 87 68 72 68 78 Small Tab 45 68 72 Large 78 Tab 68 87 46 44 47 100 101 78 Small Tab 72 87 101 100 100 63 68 87 72 78 Small Tab 48 72 Small Tab 68 78 68 87 100 2 17