Weider 9400 Instruction Manual - Page 14
Locate the Leg Lever Cable 75, which is
View all Weider 9400 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 14 highlights
29. Wrap the Lat Cable (88) around a 90mm Pulley 29 (78). Attach the Pulley and a Cable Trap (102) to the Top Frame (6) with an M10 x 50mm Bolt (100) and an M10 Nylon Locknut (87). Make sure the Cable Trap is turned to hold the Cable in the groove of the Pulley. 30. Remove the preattached 90mm Pulleys (78) 30 from the Pulley Plates (63). Wrap the Lat Cable (88) around a 90mm Pulley (78). Attach the Pulley and a pair of Pulley Covers (68) to the second set of holes from the top of the Pulley Plates (63) with an M10 x 50mm Bolt (100) and an M10 Nylon Locknut (87). Make sure the small tabs on the Pulley Covers are on the top. 31. Attach the end of the Lat Cable (88) inside of the 31 Butterfly Top Frame (7) with an M10 x 65mm Bolt (18), two M10 Washers (91), and an M10 Nylon Locknut (87). 32. Locate the Butterfly Cable (69), which is the 32 shortest Cable. Attach the Cable to the Pivot Bracket (70) on the Left Butterfly Arm (25) with an M8 x 20mm Shoulder Bolt (103) and an M8 Nylon Locknut (34). 33. Wrap the Butterfly Cable (69) over a "V"-pulley (55). 33 Attach the Pulley and a Cable Trap (102) to the indicated bracket on the Butterfly Upright (3) with an M10 x 60mm Bolt (59) and an M10 Nylon Locknut (87). Make sure that the Cable Trap is turned to hold the Cable in the groove of the Pulley. 14 88 87 78 102 100 6 68 Small Tab 78 100 68 88 87 63 87 91 91 18 7 88 34 69 103 70 25 3 87 55 102 59 69 34. Remove the preattached 90mm Pulleys (78) from the Double "U"-bracket (62). 34 Wrap the Butterfly Cable (69) under a 90mm Pulley (78). Attach the Pulley and a pair of Pulley Covers (8) to the Double "U"-bracket (62) with an M10 x 50mm Bolt (100) and an M10 Nylon Locknut (87). Make sure the small tabs on the Pulley Covers are on the top. Small Tab 68 87 69 68 78 100 62 35. Wrap the Butterfly Cable (69) over a "V"-pulley (55). 35 Attach the Pulley and a Cable Trap (102) to the 59 other side of the bracket on the Butterfly Upright (3) 102 with an M10 x 60mm Bolt (59) and an M10 Nylon 69 Locknut (87). Make sure that the Cable Trap is 3 turned to hold the Cable in the groove of the 55 Pulley. 87 36. Attach the Butterfly Cable (69) to the Pivot Bracket 36 (70) on the Right Butterfly Arm (26) with an M8 x 20mm Shoulder Bolt (103) and an M8 Nylon Locknut (34). 103 69 70 26 34 37. Locate the Leg Lever Cable (75), which is 2398mm long and has an eyelet on one end and a threaded pin on the other end. Route the eyelet end of the Cable through the Seat Upright (9) and attach it to the tab on the Leg Lever (10) with an M8 x 20mm Shoulder Bolt (103) and an M8 Nylon Locknut (34). 38. Attach a 90mm Pulley (78) inside of the Seat Upright (9) with an M10 x 65mm Bolt (18), two M10 Washers (91), two 12mm Spacers (89), and an M10 Nylon Locknut (87), as shown. 37 34 75 9 10 103 38 91 89 87 9 78 75 91 18 89 15