Weider Pro 2000 Uk Manual - Page 12

Locate the Short Cable 47.

Get Weider Pro 2000 PDF manuals and user guides View all Weider Pro 2000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

18. Wrap the Press Cable (49) under a 90mm Pulley 18 (34). Attach the Pulley and two Finger Guards (35) to the Double "U"-bracket (42) with an M10 x 46mm Bolt (53) and an M10 Nylon Locknut (68). 49 34 35 68 35 53 42 19. Apply grease to an M10 x 78mm Bolt (54). 19 Attach a Pulley Arm (38) to the Upright (3) with the Bolt and an M10 Nylon Locknut (68). Do not overtighten the Nylon Locknut; the Pulley Arm must pivot easily. Wrap the Press Cable (49) over a 90mm Pulley (34). Attach the Pulley, a Cable Trap (36), an M10 Washer (70), and two Finger Guards (35) to the indicated side of a Pulley Arm (38) with an M10 x 52mm Bolt (52) and an M10 Nylon Locknut (68). Make sure that the Cable Trap is oriented to hold the Cable in the groove of the Pulley. 52 Grease 54 38 35 68 36 34 49 70 35 68 3 20. Slide the end of the Press Cable (49) onto the hook on the Right Arm (6). 20 49 21. Locate the Short Cable (47). Attach the eyelet 21 on the Cable to the Base (1) with an M10 x 70mm Bolt (57), an M10 Washer (70), and an M10 Nylon Locknut (68). Do not overtighten the Nylon Locknut. 12 6 68 70 1 47 57

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
12
19. Apply grease to an M10 x 78mm Bolt (54).
Attach a Pulley Arm (38) to the Upright (3) with
the Bolt and an M10 Nylon Locknut (68).
Do
not overtighten the Nylon Locknut; the
Pulley Arm must pivot easily.
Wrap the Press Cable (49) over a 90mm Pulley
(34). Attach the Pulley, a Cable Trap (36), an
M10 Washer (70), and two Finger Guards (35)
to the indicated side of a Pulley Arm (38) with
an M10 x 52mm Bolt (52) and an M10 Nylon
Locknut (68).
Make sure that the Cable Trap
is oriented to hold the Cable in the groove
of the Pulley.
18. Wrap the Press Cable (49) under a 90mm Pulley
(34). Attach the Pulley and two Finger Guards
(35) to the Double “U”-bracket (42) with an M10 x
46mm Bolt (53) and an M10 Nylon Locknut (68).
34
53
68
49
35
42
35
18
35
36
49
52
38
68
68
3
54
Grease
34
35
70
19
20. Slide the end of the Press Cable (49) onto the
hook on the Right Arm (6).
49
6
20
21.
Locate the Short Cable (47).
Attach the eyelet
on the Cable to the Base (1) with an M10 x
70mm Bolt (57), an M10 Washer (70), and an
M10 Nylon Locknut (68).
Do not overtighten
the Nylon Locknut.
57
70
68
47
1
21