Weider Pro 2000 Uk Manual - Page 14

Attach the Cable Hook 30 to the Leg Lever 9

Get Weider Pro 2000 PDF manuals and user guides View all Weider Pro 2000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

26. Wrap the Low Cable (48) under a 90mm Pulley 26 (34). Attach the Pulley and two Finger Guards (35) to the bracket on the Base (1) with an M10 x 46mm Bolt (53) and an M10 Nylon Locknut (68). 27. Route the Low Cable (48) over a 90mm Pulley 27 (34). Attach the Pulley, a Cable Trap (36), and two Finger Guards (35) to the lower set of holes in the "U"-bracket (43) with an M10 x 52mm Bolt (52) and an M10 Nylon Locknut (68). Make sure that the Cable Trap is oriented to hold the Cable in the groove of the Pulley. 34 48 53 35 1 35 68 52 43 35 35 68 36 34 48 28. Route the Low Cable (48) under a 90mm Pulley 28 (34). Attach the Pulley, a Cable Trap (36), and two Guards (14) to the Upright (3) with an M10 x 100mm Bolt (46), two M10 Washers (70), and an M10 Nylon Locknut (68). Make sure that the Cable Trap is oriented to hold the Cable in the groove of the Pulley. 29. Attach the Cable Hook (30) to the Leg Lever (9) 29 with an M10 Washer (70) and an M10 Nylon Locknut (68). Attach the Low Cable (48) to the Chain (83) and to the Cable Hook (30) with two Cable Clips (33). 14 3 68 70 34 14 14 70 48 36 46 9 83 48 30 70 33 68

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
14
27. Route the Low Cable (48) over a 90mm Pulley
(34). Attach the Pulley, a Cable Trap (36), and
two Finger Guards (35) to the lower set of holes
in the “U”-bracket (43) with an M10 x 52mm
Bolt (52) and an M10 Nylon Locknut (68).
Make
sure that the Cable Trap is oriented to hold
the Cable in the groove of the Pulley.
28. Route the Low Cable (48) under a 90mm Pulley
(34). Attach the Pulley, a Cable Trap (36), and
two Guards (14) to the Upright (3) with an M10
x 100mm Bolt (46), two M10 Washers (70), and
an M10 Nylon Locknut (68).
Make sure that
the Cable Trap is oriented to hold the Cable
in the groove of the Pulley.
26.
Wrap the Low Cable (48) under a 90mm Pulley
(34). Attach the Pulley and two Finger Guards
(35) to the bracket on the Base (1) with an M10
x 46mm Bolt (53) and an M10 Nylon Locknut
(68).
35
35
68
34
1
48
53
26
34
48
35
36
35
52
43
68
27
70
48
36
70
68
14
14
34
3
28
29. Attach the Cable Hook (30) to the Leg Lever (9)
with an M10 Washer (70) and an M10 Nylon
Locknut (68).
Attach the Low Cable (48) to the Chain (83)
and to the Cable Hook (30) with two Cable
Clips (33).
70
9
68
46
48
33
83
30
29