Weider Pro 8000 Uk Manual - Page 18

Make sure the Cable Trap

Get Weider Pro 8000 PDF manuals and user guides View all Weider Pro 8000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

42. Wrap the Leg Lever Cable (70) under a 90mm 42 Pulley (39). Attach the Pulley and two Half Finger Guards (42) to the Right Base (1) with an M10 x 48mm Bolt (101) and an M10 Nylon Locknut (114). 114 42 43. Wrap the Leg Lever Cable (70) over a 90mm 43 Pulley (39). Attach the Pulley, a Small Cable Trap (48), and two Half Finger Guards (42) at the sec- ond hole from the bottom of the two Pulley Plates (51) with an M10 x 52mm Bolt (102) and an M10 Nylon Locknut (114). Make sure the Cable Trap is oriented to hold the Cable in the groove of the Pulley. 70 1 39 101 42 114 51 42 42 48 39 102 70 44. Wrap the Leg Lever Cable (70) under a 90mm 44 Pulley (39). Attach the Pulley and two Half Finger Guards (42) to the "U"-bracket on the Right Base (1) with an M10 x 48mm Bolt (101) and an M10 Nylon Locknut (114). Make sure the Finger Guards are on the outside of the "U"-bracket. 42 114 70 39 42 101 45. Wrap the Leg Lever Cable (70) under a 90mm 45 Pulley (39). Attach the Pulley, a Small Cable Trap (48), and two Half Finger Guards (42) to the bracket on the Right Base (1) with an M10 x 52mm Bolt (102) and an M10 Nylon Locknut (114). Make sure the Cable Trap is oriented to hold the Cable in the groove of the Pulley, and that the bracket is between the Pulley and the Finger Guard next to the Locknut. 46. Route the Leg Lever Cable (70) up through the 46 Right Top Frame (7) and over a 90mm Pulley (39). Attach the Pulley inside the Top Frame with an M10 x 80mm Bolt (111), two M10 Washers (116), two 19mm Spacers (77), and an M10 Nylon Locknut (114). 1 42 70 114 39 42 48 102 1 Bracket 70 39 111 7 116 77 116 77 114 18

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
18
42. Wrap the Leg Lever Cable (70) under a 90mm
Pulley (39). Attach the Pulley and two Half Finger
Guards (42) to the Right Base (1) with an M10 x
48mm Bolt (101) and an M10 Nylon Locknut
(114).
43. Wrap the Leg Lever Cable (70) over a 90mm
Pulley (39). Attach the Pulley, a Small Cable Trap
(48), and two Half Finger Guards (42) at the sec-
ond hole from the bottom of the two Pulley Plates
(51) with an M10 x 52mm Bolt (102) and an M10
Nylon Locknut (114).
Make sure the Cable Trap
is oriented to hold the Cable in the groove of
the Pulley.
44. Wrap the Leg Lever Cable (70) under a 90mm
Pulley (39). Attach the Pulley and two Half Finger
Guards (42) to the “U”-bracket on the Right Base
(1) with an M10 x 48mm Bolt (101) and an M10
Nylon Locknut (114).
Make sure the Finger
Guards are on the outside of the “U”-bracket.
45. Wrap the Leg Lever Cable (70) under a 90mm
Pulley (39). Attach the Pulley, a Small Cable Trap
(48), and two Half Finger Guards (42) to the
bracket on the Right Base (1) with an M10 x
52mm Bolt (102) and an M10 Nylon Locknut
(114).
Make sure the Cable Trap is oriented to
hold the Cable in the groove of the Pulley, and
that the bracket is between the Pulley and the
Finger Guard next to the Locknut.
46. Route the Leg Lever Cable (70) up through the
Right Top Frame (7) and over a 90mm Pulley
(39). Attach the Pulley inside the Top Frame with
an M10 x 80mm Bolt (111), two M10 Washers
(116), two 19mm Spacers (77), and an M10
Nylon Locknut (114).
42
70
39
42
42
1
101
114
43
42
42
48
39
70
114
51
102
44
70
39
42
42
101
1
114
45
114
42
39
70
42
48
1
Bracket
102
46
70
116
116
111
114
77
77
39
7