Xerox 5550N User Guide (English) - Page 57

Setting the Interface ID, Resetting the TCP/IP Configuration, Using CentreWare IS

Get Xerox 5550N - Phaser B/W Laser Printer PDF manuals and user guides
UPC - 095205737257
View all Xerox 5550N manuals
Add to My Manuals
Save this manual to your list of manuals

Page 57 highlights

IPv6 Resetting the TCP/IP Configuration Use the following procedure at the control panel to reset the TCP/IP configuration to the default settings: 1. Select Printer Setup, and then press the OK button. 2. Select Connection Setup, and then press the OK button. 3. Select Reset Connection Setup, and then press the OK button. Setting the Interface ID Your IPv6-enabled printer has one interface with multiple addresses. The Interface ID is the part of the address after the prefix. The printer uses the Interface ID when assigning both the Link-Local address and automatic addresses that use router supplied prefix(es). It is not used in addresses supplied by DHCPv6. Link-Local addresses are used by nodes to communicate with other nodes on the same local network. There are two options to set the Interface ID: ■ The default is to have the Interface ID automatically computed from the MAC address associated with the interface. The ID is different for each device. This is the recommended method for setting the Interface ID. ■ The other option is to manually set the interface ID. The Interface ID must be 64 bits (8 bytes) in length, and must not contain special characters other than colons or valid hexadecimal digits (0 through 9, a through f, or A through F). Note: If you change the Interface ID, you will be prompted to reset the printer before the changes take effect. The Interface ID can only be set in CentreWare IS. Using CentreWare IS To set the Interface ID using CentreWare IS: 1. Launch your web browser. 2. Enter your printer's IP address in the browser's Address field. 3. Click Properties. 4. Select the Protocols folder on the left navigation panel, and then click TCP/IP. 5. Click the TCP/IP (v6) button. 6. Do one of the following: ■ Select User Interface ID from MAC address. ■ Select Use this Interface ID. 7. Click the Save Changes button at the bottom of the page. Phaser® 5550 Printer 3-27

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236
  • 237
IPv6
Phaser® 5550 Printer
3-27
Resetting the TCP/IP Configuration
Use the following procedure at the control panel to reset the TCP/IP configuration to the
default settings:
1.
Select
Printer Setup
, and then press the
OK
button.
2.
Select
Connection Setup
, and then press the
OK
button.
3.
Select
Reset Connection Setup
, and then press the
OK
button.
Setting the Interface ID
Your IPv6-enabled printer has one interface with multiple addresses. The Interface ID is the
part of the address after the prefix. The printer uses the Interface ID when assigning both the
Link-Local address and automatic addresses that use router supplied prefix(es). It is not used
in addresses supplied by DHCPv6. Link-Local addresses are used by nodes to communicate
with other nodes on the same local network. There are two options to set the Interface ID:
■
The default is to have the Interface ID automatically computed from the MAC address
associated with the interface. The ID is different for each device. This is the recommended
method for setting the Interface ID.
■
The other option is to manually set the interface ID. The Interface ID must be 64 bits
(8 bytes) in length, and must not contain special characters other than colons or valid
hexadecimal digits (0 through 9, a through f, or A through F).
Note:
If you change the Interface ID, you will be prompted to reset the printer before the
changes take effect.
The Interface ID can only be set in CentreWare IS.
Using CentreWare IS
To set the Interface ID using CentreWare IS:
1.
Launch your web browser.
2.
Enter your printer’s IP address in the browser’s
Address
field.
3.
Click
Properties
.
4.
Select the
Protocols
folder on the left navigation panel, and then click
TCP/IP
.
5.
Click the
TCP/IP (v6)
button.
6.
Do one of the following:
■
Select
User Interface ID from MAC address
.
■
Select
Use this Interface ID
.
7.
Click the
Save Changes
button at the bottom of the page.