Yamaha DTX500 Owner's Manual - Page 12
Selecting the Trigger Setup, Procedure, Trigger Setup List, About Connecting Pads - pad set
UPC - 086792942155
View all Yamaha DTX500 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 12 highlights
1 Connections 5 Selecting the Trigger Setup This setting lets you select the Trigger Setup that most closely matches the trigger output levels and functions of your pads. Use the operation described below to select the Trigger Setup you want to use. ● Procedure 5-1. Press the [SHIFT] + [DRUM KIT] buttons to view Page 1 in the Trigger Setup Select display (TRG1). TRG1 1~:XP~Med~~~~~~, 5-2. Rotate the jog dial to select the Trigger Setup that matches the drum kit you are using. TRG1 5~:STD~Med~~~~~, Trigger Setup NOTE • If you want to replace some of the pads from your drum set, or if you need to solve any crosstalk problems, the operation "Trigger Setup Edit" on page 34 describes how to make a detailed setting for each pad after the above setting is done. If you have created a setup for these reasons, that setup can be saved to one of the Trigger Setup locations (8-11). ● About Connecting Pads • The DTX500's input jack parameters are preset with settings suitable for pads when an appropriate Trigger Setup is selected. If you intend to connect any other type of pad or a drum trigger (Yamaha DT20, etc.) to the input jack, that jack's parameters (sensitivity, etc.) should be changed to settings that suit the particular pad. Pad sensitivity is set in the Trigger Setup Select display's Page 3 [TRG3 Gain] setting (p. 36). • Pad-controller-equipped pads like the XP100SD, TP100, etc., can be connected to Trigger Input jack 1SNARE. • Three-zone pads like the TP65S, PCY155/150S, PCY135/ 130SC, etc., can be connected to Trigger Input jacks 5RIDE and 6CRASH. • 7HI HAT is a stereo input type jack. Pads equipped with trigger switches like the TP65S, PCY65S, PCY130S, etc. can be connected to this jack. • The 2TOM1/ 0, 3TOM2/ !, 4TOM3/ @ jacks correspond to a two-trigger input that uses a stereo jack for L and R. A Y-shaped cable (stereo plug-mono jack x 2) can be used to input two trigger signals. • The 8KICK/ 9 jack accepts a two-trigger input using a stereo cable and jack for L and R signals. A Y-shaped cable (stereo plug-mono jack x 2) can be used to input two trigger signals. Also, if the KP125W/125/65 kick pad is connected to the DTX500's input jack 9 with a stereo cable, the external pad input jack on the KP125W/125/65 can be used as the input for Input jack 9. • In addition to the 8KICK/ 9 jack, the 2TOM1/ 0, 3TOM2/ !, and 4 TOM3/ @ jacks can be used to connect a second bass drum pedal to create a double-bass drum set. ● Trigger Setup List No. Name Features 1 XP Med Normal Setting Drum Set with new pads Wide dynamic range. This setting is designed for maximum expressive control, allow- 2 XP Dyna (XP series) ing performance subtleties over a wide dynamic range. Excessive vibration however, may result in crosstalk (sound being produced by other pads). 3 SP Med 4 SP Dyna for DTXPRESS IV Special Drum Set Normal Setting Wide dynamic range. This setting is designed for maximum expressive control, allowing performance subtleties over a wide dynamic range. Excessive vibration however, may result in crosstalk (sound being produced by other pads). 5 STD Med 6 STD Dyna for DTXPRESS IV Standard Drum Set Normal Setting Wide dynamic range. This setting is designed for maximum expressive control, allowing performance subtleties over a wide dynamic range. Excessive vibration however, may result in crosstalk (sound being produced by other pads). 7 DT10/20 - Use for DT10/20 drum trigger systems applied to acoustic drums. 8 | UserTrig 11 - Allows creation of custom trigger setups. (→Settings are made using Trigger Setup Edit on page 34.) * In the default setting, "1: XP Med" is selected. 12 DTX500 Owner's Manual