Yamaha DTX500 Owner's Manual - Page 30

7 Create Your Own Original Drum Kit 16 Set the Pad Song When the pad is hit, the assigned pad song will start playback. In addition to one main song that is selected in the Song Select display, a maximum of three Pad Songs can be individually set for a Drum Kit. * This setting affects both layers ˙ and ¶. The ˙/¶ indication is not shown in the upper right corner of the display. Use the [>] button to call up the KIT16 page, then rotate the jog dial to set the Song Number to be assigned, the Repeat function, and the Playback mode. KIT16*~äkick "Song=~45áéplay, Song Number Playback mode Repeat ● Song Number off, 45-63 ... Assigns the Song Number that is assigned to the pad ● Repeat Playback Repeats playback of the song (when the song reaches the end it will start again from the beginning, continuously). Normal playback. ● Playback Mode play When the pad is hit, playback of the assigned pad song will start/stop. chse When the pad is hit, one measure of the assigned pad song will start playback then pause. ctof When the pad is hit, playback of the assigned pad song will start/stop. However, if the pad song is set to "ctof," the pad song will stop when another pad song with the "ctof" setting is started. This function allows only one "ctof" pad song to be played at a time. * Up to three pad songs can be set for each Drum Kit. To assign a pad song for other pads, hit the target pad, or press the [SHIFT] + [] buttons, so that the target pad name (trigger input source) is shown in the upper half of the display. However, when three pad songs are set, "Song=off" is shown and the settings cannot be made. * The tempo of the pad song is the same as that of the main song that is found in the Song Select display or the Click Setting display. * If a function is already assigned in the UTIL7 page to the input source that the pad song is assigned, "Song=(in use!)" is shown and the setting in the UTIL7 takes priority. (p. 21) * When multiple pad songs are assigned and played back in combination, the voices within the songs may change unexpectedly or sound different than intended. 17 Set the Rim to Pad This function is effective only when the input source is from a rim switch. When the rim is hit, pad events triggered from the same pad (trigger input jack) can be simultaneously transmitted with rim switch events. With this setting, a snare pad's sound can be triggered at the same time as the snare's rim shot. * This setting affects both layers ˙ and ¶. The ˙/¶ indication is not shown in the upper right corner of the display. * When an input other than the rim switch is selected for the input source, "RimToPad=---" will be displayed and the settings cannot be made. The following display appears when "ƒsnrOp" is selected for the input source. Use the [>] button to call up the KIT17 page, then rotate the jog dial to set the Rim to Pad. KIT17*~ƒsnrOp "~RimToPad=off~, off Only transmits rim switch event. on Transmits both rim switch event and pad event. 18 Change the Reverb Level (1) This determines the Reverb Send Level for the voices (layers 1, 2) triggered by the input source. This effectively allows you to adjust the reverb depth. * This setting affects both layers ˙ and ¶. The ˙/¶ indication is not shown in the upper right corner of the display. * The actual Reverb Send Level is determined by adding the Send Level set here to the Drum Reverb Send Level set in the KIT19 page. Use the [>] button to call up the KIT18 page, then rotate the jog dial to set the Reverb Send Level (0-127). KIT18*~äkick "~RevSend=~30~~, 19 Change the Reverb Level (2) This determines the Overall Reverb Send Level of the Drum Voice. * This setting affects the entire Drum Voice. The ˙/¶ indication is not shown in the upper right corner of the display. Use the [>] button to call up the KIT19 page, then rotate the jog dial to set the Drum Reverb Send Level (0-127). KIT19* "~RevSendDr=~40, 30 DTX500 Owner's Manual