Yamaha HTR 5790 MCXSP10 Manual - Page 72

ZONE 2/ZONE 3 (U.S.A., CANADA AND AUSTRALIA MODELS ONLY), Zone 2/Zone 3 connections

Get Yamaha HTR 5790 - Digital Home Theater Receiver PDF manuals and user guides
UPC - 027108919744
View all Yamaha HTR 5790 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 72 highlights

ZONE 2/ZONE 3 (U.S.A., CANADA AND AUSTRALIA MODELS ONLY) ZONE 2/ZONE 3 (U.S.A., CANADA AND AUSTRALIA MODELS ONLY) This unit allows you to configure a multi-room audio system. The Zone 2 and Zone 3 features enable you to set this unit to reproduce separate input sources in the main room, second room (Zone 2) and third room (Zone 3). You can control this unit from the second room using the supplied remote control. Only analog signals are sent to the second and third rooms. Any source you want to listen to in the second or third room must be connected using the analog (AUDIO L/R) input jacks on this unit. Zone 2/Zone 3 connections You need the following additional equipment to use the multi-room functions of this unit: • An infrared signal receiver in the second and/or third room. • An infrared emitter in the main room. This emitter transmits the infrared signals from the remote control in the second and/or third room to the main room (to a CD player or LD player, for example). • An amplifier and speakers for the second and/or third room. y REMOTE • Since there are many possible ways to connect and use this unit OUT IN OUT IN CONTROL OUT in a multi-room installation, we recommend that you consult with the nearest authorized YAMAHA dealer or service center This unit for the Zone 2/Zone 3 connections which will best meet your requirements. • Some YAMAHA models are able to connect directly to the REMOTE CONTROL OUT jack of this unit. If you own these products, you may not need to use an infrared emitter. Up to 6 YAMAHA components can be connected as shown. ■ System configuration and connections example Using external amplifiers To use an external amplifier in Zone 2, select OFF in ZONE2 AMP. ZONE 2 AUDIO OUT ZONE 3 AUDIO OUT DVD player (or other component) This unit DVD INPUT Infrared emitter Main room Amplifier Remote control Infrared signal receiver Second room Amplifier Third room REMOTE CONTROL OUT ZONE 2 REMOTE IN Notes • When not using the main room, turn down the volume of this unit in the main room. Adjust the ZONE 2/ZONE 3 volume by using the amplifier in the second/third room. When using the remote control to adjust the ZONE 2 volume, set the volume of the amplifier in the second room to the maximum level you will use, and select VAR. in ZONE 2 SET OUTPUT VOL (page 58). • To avoid unexpected noise, DO NOT USE the Zone 2/Zone 3 feature with CDs encoded in DTS. 68

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
ZONE 2/ZONE 3 (U.S.A., CANADA AND AUSTRALIA MODELS ONLY)
68
This unit allows you to configure a multi-room audio system. The Zone 2 and Zone 3 features enable you to set this unit
to reproduce separate input sources in the main room, second room (Zone 2) and third room (Zone 3). You can control
this unit from the second room using the supplied remote control.
You need the following additional equipment to use the multi-room functions of this unit:
•
An infrared signal receiver in the second and/or third room.
•
An infrared emitter in the main room. This emitter transmits the infrared signals from the remote control in the second
and/or third room to the main room (to a CD player or LD player, for example).
•
An amplifier and speakers for the second and/or third room.
y
•
Since there are many possible ways to connect and use this unit
in a multi-room installation, we recommend that you consult
with the nearest authorized YAMAHA dealer or service center
for the Zone 2/Zone 3 connections which will best meet your
requirements.
•
Some YAMAHA models are able to connect directly to the
REMOTE CONTROL OUT jack of this unit. If you own these
products, you may not need to use an infrared emitter. Up to 6
YAMAHA components can be connected as shown.
■
System configuration and connections example
Using external amplifiers
To use an external amplifier in Zone 2, select OFF in ZONE2 AMP.
•
When not using the main room, turn down the volume of this unit in the main room. Adjust the ZONE 2/ZONE 3 volume by using the
amplifier in the second/third room. When using the remote control to adjust the ZONE 2 volume, set the volume of the amplifier in the
second room to the maximum level you will use, and select VAR. in ZONE 2 SET OUTPUT VOL (page 58).
•
To avoid unexpected noise, DO NOT USE the Zone 2/Zone 3 feature with CDs encoded in DTS.
ZONE 2/ZONE 3
(U.S.A., CANADA AND AUSTRALIA MODELS ONLY)
Only analog signals are sent to the second and third rooms. Any source you want to listen to in the second or third
room must be connected using the analog (AUDIO L/R) input jacks on this unit.
Zone 2/Zone 3 connections
OUT
IN
OUT
IN
REMOTE
CONTROL OUT
This unit
Notes
REMOTE CONTROL OUT
DVD INPUT
ZONE 2 REMOTE IN
ZONE 2 AUDIO OUT
ZONE 3 AUDIO OUT
This unit
Infrared emitter
DVD player
(or other component)
Amplifier
Remote control
Infrared signal
receiver
Amplifier
Second room
Third room
Main room