Yamaha RXV465 Owner's Manual - Page 21

Connecting the FM and AM antennas, Connecting the power cable, Turning this unit on and off - no video

Get Yamaha RXV465 - RX AV Receiver PDF manuals and user guides
UPC - 027108933214
View all Yamaha RXV465 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 21 highlights

INTRODUCTION PREPARATION BASIC OPERATION Connections Connecting the FM and AM antennas An indoor FM antenna and an AM loop antenna are supplied with this unit. Connect these antennas properly to the respective jacks. Connecting the power cable After all connections are complete, plug the AC power cable of this unit into an AC wall outlet. Indoor FM antenna Outdoor AM antenna Connect a 5 to 10 m (16 to 33 ft) vinyl-covered wire, and extend it outdoors (use the AM loop antenna together with this antenna). AM loop antenna DOCK COMPONENT VIDEO PR PB Y VIDEO HDMI OUT ANTENNA UNBAL. (BD/DVD) HDMI 1 COMPONENT VIDEO PR HDMI 2 FM GND AM PB Y VIDEO MONITOR OUT HDMI 3 F Ground (GND terminal) The GND terminal is not for earth grounding. To reduce noises, connect a ground bar or a vinyl-covered wire with a copper plate at its tip, and place it in the moist ground. y • The supplied antennas are normally sensitive enough to obtain good reception. • Position the AM loop antenna away from this unit. • If you cannot get good reception, we recommend that you use an outdoor antenna. For more details, consult the nearest authorized Yamaha dealer or service center. • Always use the AM loop antenna even when the outdoor antenna is connected. Assembling the AM loop antenna To the AC wall outlet Power cable Turning this unit on and off 1 Press ASTANDBY/ON on the front panel (or fPOWER on the remote control) to turn on this unit. 2 Press ASTANDBY/ON (or fPOWER) again to turn off this unit (standby mode). y • The unit needs a few seconds until ready to play back. • You can also turn on this unit by pressing ISCENE (or kSCENE). • This unit consumes a small amount of electricity even in the standby mode. We recommend disconnecting the power cable from the AC wall outlet. Caution Do not unplug this unit while it is turned on. Doing so may damage this unit or cause the settings of this unit to be saved incorrectly. Connecting the AM loop antenna The wires of the AM loop antenna have no polarity. You can connect either wire to the AM terminal and the other to the GND terminal. Press and hold Insert Release ADVANCED OPERATION ADDITIONAL INFORMATION APPENDIX English 17 En

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
17
En
Connections
English
INTRODUCTION
ADDITIONAL
INFORMATION
APPENDIX
PREPARATION
BASIC
OPERATION
ADVANCED
OPERATION
An indoor FM antenna and an AM loop antenna are
supplied with this unit. Connect these antennas properly to
the respective jacks.
y
•
The supplied antennas are normally sensitive enough to obtain good
reception.
•
Position the AM loop antenna away from this unit.
•
If you cannot get good reception, we recommend that you use an outdoor
antenna. For more details, consult the nearest authorized Yamaha dealer
or service center.
•
Always use the AM loop antenna even when the outdoor antenna is
connected.
Assembling the AM loop antenna
Connecting the AM loop antenna
The wires of the AM loop antenna have no polarity. You
can connect either wire to the AM terminal and the other
to the GND terminal.
After all connections are complete, plug the AC power
cable of this unit into an AC wall outlet.
1
Press
A
STANDBY/ON
on the front panel (or
f
POWER
on the remote control) to turn on
this unit.
2
Press
A
STANDBY/ON
(or
f
POWER
) again
to turn off this unit (standby mode).
y
•
The unit needs a few seconds until ready to play back.
•
You can also turn on this unit by pressing
I
SCENE
(or
k
SCENE
).
•
This unit consumes a small amount of electricity even in the standby
mode. We recommend disconnecting the power cable from the AC wall
outlet.
Connecting the FM and AM antennas
UNBAL.
FM
GND
AM
ANTENNA
P
R
P
B
Y
COMPONENT
VIDEO
DOCK
VIDEO
P
R
P
B
Y
VIDEO
HDMI
HDMI 1
(
BD/DVD
)
HDMI 2
HDMI 3
OUT
VIDEO
MONITOR OUT
F
COMPONENT
Outdoor AM antenna
Connect a 5 to 10 m (16
to 33 ft) vinyl-covered
wire, and extend it
outdoors (use the AM
loop antenna together
with this antenna).
Ground (GND terminal)
The GND terminal is not for earth
grounding.
To reduce noises, connect a ground bar or a
vinyl-covered wire with a copper plate at its
tip, and place it in the moist ground.
Indoor FM antenna
AM loop
antenna
Press and hold
Release
Insert
Connecting the power cable
Turning this unit on and off
Caution
Do not unplug this unit while it is turned on. Doing so
may damage this unit or cause the settings of this unit
to be saved incorrectly.
To the AC wall outlet
Power cable