3Com 3C16476A User Guide - Page 44

Speed/Duplex for 1000, Mbps Connections, Detail, Setup

Get 3Com 3C16476A - Baseline Switch 2250 PDF manuals and user guides
UPC - 662705475448
View all 3Com 3C16476A manuals
Add to My Manuals
Save this manual to your list of manuals

Page 44 highlights

44 CHAPTER 4: CONFIGURING THE SWITCH Figure 38 Port Administration Summary Screen Figure 39 Port Administration Detail Screen Detail Use the Detail tab to display detailed port setting information for a port. Setup Use the Setup tab to configure the port settings. The following options are available: ■ Port State - Enables and disables the port. ■ Flow Control - Enables and disables flow control for the entire Switch. When flow control is enabled, the Switch regulates the packet flow so that a sending device does not transmit more packets than a receiving device can process. If flow control is disabled, packets may be dropped under certain periods of high traffic. Flow control is disabled by default. ■ Speed - Sets the speed mode of the port. Available options include auto, 10, 100, and 1000. For 1000 Mbps connections, see "Speed/Duplex for 1000 Mbps Connections" below. Auto (or autonegotiation) sets the optimum combination of speed and duplex that can be supported by both ends of the link.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
44
C
HAPTER
4: C
ONFIGURING
THE
S
WITCH
Figure 38
Port Administration Summary Screen
Detail
Use the
Detail
tab to display detailed port setting
information for a port.
Figure 39
Port Administration Detail Screen
Setup
Use the
Setup
tab to configure the port settings. The
following options are available:
■
Port State – Enables and disables the port.
■
Flow Control – Enables and disables flow control
for the entire Switch. When flow control is
enabled, the Switch regulates the packet flow so
that a sending device does not transmit more
packets than a receiving device can process. If flow
control is disabled, packets may be dropped under
certain periods of high traffic.
Flow control is disabled by default.
■
Speed – Sets the speed mode of the port. Available
options include auto, 10, 100, and 1000. For 1000
Mbps connections, see
“
Speed/Duplex for 1000
Mbps Connections
”
below.
Auto (or autonegotiation) sets the optimum
combination of speed and duplex that can be
supported by both ends of the link.