Asus P2B98-XV P2B98-XV User Manual - Page 21

ASUS P2B98-XV User's Manual, Mount the Heatsink, Insert the SEC Cartridge

Get Asus P2B98-XV PDF manuals and user guides View all Asus P2B98-XV manuals
Add to My Manuals
Save this manual to your list of manuals

Page 21 highlights

Lock Lock III. INSTALLATION CPU III. INSTALLATION 2. Mount the Heatsink: Place the SEC cartridge face down on a flat surface and lay the heatsink flush on the back (metal side) of the SEC cartridge. Be sure that the heatsink is firmly pressed against the SEC cartridge. When correctly installed, no light must be showing through between the thermal pad of the heatsink and the SEC cartridge. WARNING! If the heatsink is not mounted tightly against the SEC cartridge, the CPU will overheat. You may install an auxiliary fan to provide adequate circulation across the processor's passive heatsink. Push each end of the clamps until they lock The thermal pad & SEC cartridge should not have a gap! SEC Cartridge with Heatsink (Top View) 3. Insert the SEC Cartridge: Push the SEC cartridge's two locks inward (the preceding picture shows the locks in the outward position and inward in the picture below). With the heatsink facing the motherboard's chipset, press the cartridge gently but firmly until it is full inserted. Push lock inward ASUS P2B98-XV User's Manual 21

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
ASUS P2B98-XV User’s Manual
21
CPU
III.
INSTALLATION
III. INSTALLATION
2.
Mount the Heatsink:
Place the SEC cartridge face down on a flat surface and lay
the heatsink flush on the back (metal side) of the SEC cartridge. Be sure that the
heatsink is firmly pressed against the SEC cartridge. When correctly installed,
no light must be showing through between the thermal pad of the heatsink and
the SEC cartridge.
WARNING!
If the heatsink is not mounted tightly against the SEC cartridge,
the CPU will overheat. You may install an auxiliary fan to provide adequate
circulation across the processor’s passive heatsink.
SEC Cartridge with Heatsink (Top View)
Push each end of the clamps until they lock
The thermal pad & SEC cartridge should not have a gap!
Lock
Lock
3.
Insert the SEC Cartridge:
Push the SEC cartridge’s two locks inward (the
preceding picture shows the locks in the outward position and inward in the
picture below). With the heatsink facing the motherboard’s chipset, press the
cartridge gently but firmly until it is full inserted.
Push lock inward