Asus P2B98-XV P2B98-XV User Manual - Page 30

ATX Power Switch / Soft Power Switch 2-pin PWR - driver

Get Asus P2B98-XV PDF manuals and user guides View all Asus P2B98-XV manuals
Add to My Manuals
Save this manual to your list of manuals

Page 30 highlights

III. INSTALLATION Connectors III. INSTALLATION 14. Message LED Lead (2-pin MLED) This indicates whether a message has been received from a fax/modem. The LED will remain lit when there is no signal and blink when there is data transfer or mail waiting in the inbox. This function requires ACPI OS and driver support. 15. System Management Interrupt (SMI) Lead (2-pin SMI) This allows the user to manually place the system into a suspend mode or "Green" mode where system activity will be instantly decreased to save electricity and expand the life of certain components when the system is not in use. This 2-pin connector (see the figure below) connects to the case-mounted suspend switch. If you do not have a switch for the connector, you may use the "Turbo Switch" since it does not have a function. SMI is activated when it detects a short to open moment and therefore leaving it shorted will not cause any problems. May require one or two pushes depending on the position of the switch. Wake-up can be controlled by settings in the BIOS but the keyboard will always allow wakeup (the SMI lead cannot wake-up the system). 16. Speaker Connector (4-pin SPEAKER) This 4-pin connector connects to the case-mounted speaker. 17. ATX Power Switch / Soft Power Switch (2-pin PWR) The system power is controlled by a momentary switch connected to this lead. Pushing the button once will switch the system between ON and SLEEP. Pushing the switch while in the ON mode for more than 4 seconds will turn the system off. The system power LED shows the status of the system's power. 18. System Power LED (3-pin PLED) This 3-pin connector connects the system power LED, which lights when the system is powered on and blinks when it is in sleep mode. 19. Reset Switch Lead (2-pin RESET) This 2-pin connector connects to the case-mounted reset switch for rebooting your computer without having to turn off your power switch This is a preferred method of rebooting in order to prolong the life of the system's power supply. Message LED SMI Speaker Ground ATX Power Switch Reset Switch IDE LED Power LED P2B98-XV System Panel Connections 30 ASUS P2B98-XV User's Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
30
ASUS P2B98-XV User’s Manual
Connectors
III.
INSTALLATION
III. INSTALLATION
14. Message LED Lead (2-pin MLED)
This indicates whether a message has been received from a fax/modem.
The
LED will remain lit when there is no signal and blink when there is data transfer
or mail waiting in the inbox. This function requires ACPI OS and driver support.
15. System Management Interrupt (SMI) Lead (2-pin SMI)
This allows the user to manually place the system into a suspend mode or “Green”
mode where system activity will be instantly decreased to save electricity and
expand the life of certain components when the system is not in use.
This 2-pin
connector (see the figure below) connects to the case-mounted suspend switch.
If you do not have a switch for the connector, you may use the “Turbo Switch”
since it does not have a function.
SMI is activated when it detects a
short to
open
moment and therefore leaving it shorted will not cause any problems.
May
require one or two pushes depending on the position of the switch.
Wake-up can
be controlled by settings in the BIOS but the keyboard will always allow wake-
up (the SMI lead cannot wake-up the system).
16. Speaker Connector (4-pin SPEAKER)
This 4-pin connector connects to the case-mounted speaker.
17. ATX Power Switch / Soft Power Switch (2-pin PWR)
The system power is controlled by a momentary switch connected to this lead.
Pushing the button once will switch the system between ON and SLEEP.
Push-
ing the switch while in the ON mode for more than 4 seconds will turn the
system off.
The system power LED shows the status of the system’s power.
18.
System Power LED (3-pin PLED)
This 3-pin connector connects the system power LED, which lights when the
system is powered on and blinks when it is in sleep mode.
19. Reset Switch Lead (2-pin RESET)
This 2-pin connector connects to the case-mounted reset switch for rebooting
your computer without having to turn off your power switch
This is a preferred
method of rebooting in order to prolong the life of the system’s power supply.
Message LED
SMI
Speaker
Reset Switch
Power LED
IDE LED
ATX Power Switch
Ground
P2B98-XV System Panel Connections