Asus P3PH4 P3-PH4 User''s Manual for English Edition - Page 52

Connectors

Get Asus P3PH4 PDF manuals and user guides View all Asus P3PH4 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 52 highlights

4.3 Connectors 4.3.1 Rear panel connectors Refer to section "1.3 Rear panel" for a description of the rear panel I/O ports. 4.3.2 Internal connectors 1 . Primary IDE connector (40-1 pin PRI_IDE) This connector is for an Ultra DMA 100/66 signal cable. The Ultra DMA 100/66 signal cable has three connectors: a blue connector for the primary IDE connector on the motherboard, a black connector for an Ultra DMA 100/66 IDE slave device (optical drive/hard disk drive), and a gray connector for an Ultra DMA 100/66 IDE master device (hard disk drive). If you install an optical drive and an IDE HDD, you must configure the optical drive as a slave device by setting its jumper accordingly. Refer to the optical drive or HDD documentation for the jumper settings. • Pin 20 on the IDE connector is removed to match the covered hole on the Ultra DMA cable connector. This prevents incorrect insertion when you connect the IDE cable. • Use the 80-conductor IDE cable for Ultra DMA 100/66 IDE devices. PRI_IDE NOTE: Orient the red markings (usually zigzag) on the IDE ribbon cable to PIN 1. ® IDE connector PIN 1 4-4 Chapter 4: Motherboard info

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
4-4
4-4
4-4
4-4
4-4
Chapter 4: Motherboard info
Chapter 4: Motherboard info
Chapter 4: Motherboard info
Chapter 4: Motherboard info
Chapter 4: Motherboard info
4.3
Connectors
4.3.1
4.3.1
4.3.1
4.3.1
4.3.1
Rear panel connectors
Rear panel connectors
Rear panel connectors
Rear panel connectors
Rear panel connectors
Refer to section “1.3 Rear panel” for a description of the rear panel I/O ports.
4.3.2
4.3.2
4.3.2
4.3.2
4.3.2
Internal connectors
Internal connectors
Internal connectors
Internal connectors
Internal connectors
1.
1.
1.
1.
1.
Primary IDE connector (40-1 pin PRI_IDE)
Primary IDE connector (40-1 pin PRI_IDE)
Primary IDE connector (40-1 pin PRI_IDE)
Primary IDE connector (40-1 pin PRI_IDE)
Primary IDE connector (40-1 pin PRI_IDE)
This connector is for an Ultra DMA 100/66 signal cable. The Ultra
DMA 100/66 signal cable has three connectors: a blue connector for
the primary IDE connector on the motherboard, a black connector for
an Ultra DMA 100/66 IDE slave device (optical drive/hard disk drive),
and a gray connector for an Ultra DMA 100/66 IDE master device (hard
disk drive). If you install an optical drive and an IDE HDD, you must
configure the optical drive as a slave device by setting its jumper
accordingly. Refer to the optical drive or HDD documentation for the
jumper settings.
•
Pin 20 on the IDE connector is removed to match the covered hole
on the Ultra DMA cable connector. This prevents incorrect insertion
when you connect the IDE cable.
•
Use the 80-conductor IDE cable for Ultra DMA 100/66 IDE devices.
IDE connector
NOTE:
Orient the red markings
(usually zigzag) on the IDE
ribbon cable to PIN 1.
PRI_IDE
PIN 1