Asus P5VDC-MX V2.0 Motherboard DIY Troubleshooting Guide - Page 42

pin ATX12V

Get Asus P5VDC-MX V2.0 PDF manuals and user guides View all Asus P5VDC-MX V2.0 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 42 highlights

7. ATX power connectors (24-pin EATXPWR, 4-pin ATX12V) These connectors are for an ATX power supply. The plugs from the power supply are designed to fit these connectors in only one orientation. Find the proper orientation and push down firmly until the connectors completely fit. • Do not forget to connect the 4-pin ATX +12 V power plug; otherwise, the system will not boot up. • When using an ATX 12 V PSU with 20-pin power plug, make sure that it can provide 8 A on the +12 V lead and at least 1A on the +5V standby lead (+5 VSB). The minimum recommended wattage is 300 W, or 350 W for a fully configured system. The system may become unstable or may not boot up if the power is inadequate. • You must install a Power Supply Unit (PSU) with a higher power rating if you intend to install additional devices. EATXPWR ATX12V GND +12V DC GND +12V DC P5VDC-MX ® P5VDC-MX ATX power connectors +3 Volts -12 Volts Ground PSON# Ground Ground Ground -5 Volts +5 Volts +5 Volts +5 Volts Ground +3 Volts +3 Volts Ground +5 Volts Ground +5 Volts Ground Power OK +5V Standby +12 Volts +12 Volts +3 Volts 1-30 Chapter 1: Product introduction

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
1-30
1-30
1-30
1-30
1-30
Chapter 1: Product introduction
Chapter 1: Product introduction
Chapter 1: Product introduction
Chapter 1: Product introduction
Chapter 1: Product introduction
7.
7.
7.
7.
7.
ATX power connectors (24-pin EATXPWR,
ATX power connectors (24-pin EATXPWR,
ATX power connectors (24-pin EATXPWR,
ATX power connectors (24-pin EATXPWR,
ATX power connectors (24-pin EATXPWR,
4-pin ATX12V)
4-pin ATX12V)
4-pin ATX12V)
4-pin ATX12V)
4-pin ATX12V)
These connectors are for an ATX power supply. The plugs from the
power supply are designed to fit these connectors in only one
orientation. Find the proper orientation and push down firmly until the
connectors completely fit.
•
Do not forget to connect the 4-pin ATX +12 V power plug;
otherwise, the system will not boot up.
•
When using an ATX 12 V PSU with 20-pin power plug, make sure
that it can provide 8 A on the +12 V lead and at least 1A on the
+5V standby lead (+5 VSB). The minimum recommended wattage is
300 W, or 350 W for a fully configured system. The system may
become unstable or may not boot up if the power is inadequate.
•
You must install a Power Supply Unit (PSU) with a higher power
rating if you intend to install additional devices.
P5VDC-MX
P5VDC-MX ATX power connectors
EATXPWR
ATX12V
+12V DC
GND
+12V DC
GND
+3 Volts
+3 Volts
Ground
+5 Volts
+5 Volts
Ground
Ground
Power OK
+5V Standby
+12 Volts
-5 Volts
+5 Volts
+3 Volts
-12 Volts
Ground
Ground
Ground
PSON#
Ground
+5 Volts
+12 Volts
+3 Volts
+5 Volts
Ground