Asus TRL-DLS TRL-DLS User Manual - Page 21

Expansion Slots

Get Asus TRL-DLS PDF manuals and user guides View all Asus TRL-DLS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 21 highlights

3. H/W SETUP Expansion Cards 3. HARDWARE SETUP 3.7 Expansion Slots WARNING! Unplug the power supply when adding or removing expansion cards or other system components. Failure to do so may cause severe damage to both your motherboard and expansion cards. In the future, you may need to install expansion cards. The motherboard has four 3.3V 64-bit/66MHz PCI slots and two 5V 32-bit/33MHz PCI slots. The slots support PCI 2.2 protocol. 3.7.1 Expansion Card Installation Procedure Follow these steps to install an expansion card. 1. Before installing the expansion card, read the documentation that came with it and make the necessary hardware settings for the card. 2. Remove the system unit cover (if your motherboard is already installed in a chassis). 3. Remove the bracket opposite the slot that you intend to use. Keep the screw for later use. 4. Align the card connector with the slot and press firmly until the card is completely seated on the slot. 5. Secure the card to the chassis with the screw you removed earlier. 6. Replace the system cover. 3.7.2 Configuring an Expansion Card After physically installing the expansion card, configure the card by adjusting the software settings. 1. Turn on the system and change the necessary BIOS settings, if any. See Chapter 4 for information on BIOS setup. 2. Assign an IRQ to the card. Refer to the tables on the next page. 3. Install the software drivers for the expansion card. ASUS TRL-DLS User's Manual 21

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
ASUS TRL-DLS User’s Manual
21
3. HARDWARE SETUP
3.7
Expansion Slots
WARNING!
Unplug the power supply when adding or removing expansion cards
or other system components. Failure to do so may cause severe damage to both
your motherboard and expansion cards.
3.7.1
Expansion Card Installation Procedure
Follow these steps to install an expansion card.
1.
Before installing the expansion card, read the documentation that came with it
and make the necessary hardware settings for the card.
2.
Remove the system unit cover (if your motherboard is already installed in a
chassis).
3.
Remove the bracket opposite the slot that you intend to use. Keep the screw for
later use.
4.
Align the card connector with the slot and press firmly until the card is completely
seated on the slot.
5.
Secure the card to the chassis with the screw you removed earlier.
6.
Replace the system cover.
Expansion Cards
3. H/W SETUP
In the future, you may need to install expansion cards. The motherboard has four
3.3V 64-bit/66MHz PCI slots and two 5V 32-bit/33MHz PCI slots. The slots support
PCI 2.2 protocol.
3.7.2
Configuring an Expansion Card
After physically installing the expansion card, configure the card by adjusting the
software settings.
1.
Turn on the system and change the necessary BIOS settings, if any. See Chapter
4 for information on BIOS setup.
2.
Assign an IRQ to the card. Refer to the tables on the next page.
3.
Install the software drivers for the expansion card.