Bernina 2500DCET Manual - Page 73

Trouble shooting guide

Get Bernina 2500DCET PDF manuals and user guides View all Bernina 2500DCET manuals
Add to My Manuals
Save this manual to your list of manuals

Page 73 highlights

2500_DCE_2_englisch_neu 09.10.2007 15:02 Uhr Seite 73 Trouble shooting guide Problem: Cause: Solution: Seams pucker: Differential feed is set incorrectly. Adjust differential feed to 0.7 - N. Needle thread tensions are too tight. Reduce needle thread tensions. Looper thread tension is too tight for thread. Use the Deco Guide. Fabric edges curl: Too much fabric in the stitch. Reduce the cutting width. Stitch selection lever is on roll hem. Set selection lever to overlock. Thread loops are too loose. Too little fabric in the stitch. Increase the cutting width. Machine stops sewing: Should the machine stops sewing, the motor cuts out for 2 seconds, afterwards you can continue sewing. Check why the machine stopped. The machine will sew again after the safety cut out. Fabric cannot be removed: (cover stitch and top & bottom cover stitch) Handwheel was turned anticlockwise. Insert needles into fabric, press Needle stop, turn the handwheel away from you (clockwise) to raise needles. Remove work. 73

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
73
Trouble shooting guide
Problem:
Cause:
Solution:
Seams pucker:
Differential feed is
Adjust differential feed to 0.7 - N.
set incorrectly.
Needle thread tensions
Reduce needle thread tensions.
are too tight.
Looper thread tension is
Use the Deco Guide.
too tight for thread.
Fabric edges curl:
Too much fabric in the stitch.
Reduce the cutting width.
Stitch selection lever is
Set selection lever to overlock.
on roll hem.
Thread loops are too loose.
Too little fabric in the stitch.
Increase the cutting width.
Machine stops sewing:
Should the machine stops
Check why the machine stopped. The machine will sew
sewing, the motor cuts out
again after the safety cut out.
for 2 seconds, afterwards
you can continue sewing.
Fabric cannot be removed:
Handwheel was turned anti-
Insert needles into fabric, press Needle stop, turn the
(cover stitch and
clockwise.
handwheel away from you (clockwise) to raise needles.
top & bottom cover stitch)
Remove work.
2500_DCE_2_englisch_neu
09.10.2007 15:02 Uhr
Seite 73