Brother International CS-8060 Users Manual - English - Page 19

CAUTION, the spool cap is too small for the spool - bobbin winder

Get Brother International CS-8060 PDF manuals and user guides View all Brother International CS-8060 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

CONTENTS GETTING READY SEWING BASICS UTILITY STITCHES Slide the bobbin winder shaft to the right. 5 Place the spool of thread for the bobbin onto 6 the bobbin thread spool pin. CAUTION ● Two spool cap sizes are available, allowing you to choose a spool cap that best fits the size of spool being used. If the spool cap is too small for the spool being used, the thread may catch on the slit in the spool or the needle may break. Slide the spool cap onto the bobbin thread 7 spool pin. With the rounded side of the spool cap positioned toward the left, slide the spool cap onto the bobbin thread spool pin as far as possible until the right side of the spool touches the right end of the bobbin thread spool pin. Note ● If a spool of thread 12 mm (1/2 inch) in diameter and 75 mm (3 inch) high is inserted onto the bobbin thread spool pin, use the special spool cap. 2 1 1 12 mm (1/2 inch) 2 75 mm (3 inch) APPENDIX INDEX Winding/Installing the Bobbin 13

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
Winding/Installing the Bobbin
13
GETTING READY
CONTENTS
SEWING BASICS
UTILITY STITCHES
APPENDIX
INDEX
5
Slide the bobbin winder shaft to the right.
6
Place the spool of thread for the bobbin onto
the bobbin thread spool pin.
7
Slide the spool cap onto the bobbin thread
spool pin.
With the rounded side of the spool cap
positioned toward the left, slide the spool cap
onto the bobbin thread spool pin as far as
possible until the right side of the spool
touches the right end of the bobbin thread
spool pin.
Note
●
If a spool of thread 12 mm (1/2 inch) in
diameter and 75 mm (3 inch) high is
inserted onto the bobbin thread spool pin,
use the special spool cap.
1
12 mm (1/2 inch)
2
75 mm (3 inch)
●
Two spool cap sizes are available,
allowing you to choose a spool cap that
best fits the size of spool being used. If
the spool cap is too small for the spool
being used, the thread may catch on the
slit in the spool or the needle may break.
CAUTION
1
2