Brother International RJ4040-K RuggedJet w/WiFi Battery User Guide - Page 19

Advanced, Name SSID, Network Key, ATTENTION, Cancel, Change IP, Address, Retry, Wireless

Get Brother International RJ4040-K RuggedJet w/WiFi Battery PDF manuals and user guides View all Brother International RJ4040-K RuggedJet w/WiFi Battery manuals
Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

• If your access point is set to not broadcast the SSID, you can enter the SSID manually by clicking the [Advanced] button. Follow the on-screen instructions for entering the [Name (SSID)], and then click [Next]. g Enter the [Network Key] you noted in MEMO uu page 11 and then click [Next]. Setting Up the Printer • If you want to manually assign an IP address to the printer, click [Change IP Address] and enter an IP address that is 1 compatible with your network. • If the wireless setup failure screen appears, click [Retry]. i Disconnect the USB cable connecting the computer and the printer and then click [Next]. Wireless setup is now complete. Go on to j to install the printer driver and the software. j Choose the printer from the list, and then click [Next]. Note If your network is not configured for authentication and encryption, the [ATTENTION!] screen will appear. To continue configuration, click [OK] and go to h. h Confirm the wireless network settings and then click [Next]. The settings will be sent to your printer. Note • The settings will remain unchanged if you click [Cancel]. Note • If your wireless settings fail, the [Wireless Device Setup Wizard] screen appears. Follow the on-screen instructions to complete the wireless configuration. • If you are using WEP but your printer is not found, make sure you entered the WEP key correctly. k Follow the on-screen instructions to complete setup. DO NOT cancel any of the screens during the installation. It may take a few seconds for all screens to appear. 15

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
Setting Up the Printer
15
1
•
If your access point is set to not broadcast
the SSID, you can enter the SSID
manually by clicking the [
Advanced
]
button. Follow the on-screen instructions
for entering the [
Name (SSID)
], and then
click [
Next
].
g
Enter the [
Network Key
] you noted in
MEMO
uu
page 11 and then click
[
Next
].
Note
If your network is not configured for
authentication and encryption, the
[
ATTENTION!
] screen will appear. To
continue configuration, click [
OK
] and go
to
h
.
h
Confirm the wireless network settings
and then click [
Next
]. The settings will
be sent to your printer.
Note
•
The settings will remain unchanged if you
click [
Cancel
].
•
If you want to manually assign an IP
address to the printer, click [
Change IP
Address
] and enter an IP address that is
compatible with your network.
•
If the wireless setup failure screen
appears, click [
Retry
].
i
Disconnect the USB cable connecting
the computer and the printer and then
click [
Next
].
Wireless setup is now complete.
Go on to
j
to install the printer driver
and the software.
j
Choose the printer from the list, and
then click [
Next
].
Note
•
If your wireless settings fail, the [
Wireless
Device Setup Wizard
] screen appears.
Follow the on-screen instructions to
complete the wireless configuration.
•
If you are using WEP but your printer is
not found, make sure you entered the
WEP key correctly.
k
Follow the on-screen instructions to
complete setup.
DO NOT cancel any of the screens
during the installation. It may take a few
seconds for all screens to appear.