Brother International Z-8550A Instruction Manual - English - Page 49

Adjusting the needle up stop position, USING THE OPERATION PANEL ADVANCED OPERATIONS

Get Brother International Z-8550A PDF manuals and user guides View all Brother International Z-8550A manuals
Add to My Manuals
Save this manual to your list of manuals

Page 49 highlights

7. USING THE OPERATION PANEL (ADVANCED OPERATIONS) 7-2. Adjusting the needle up stop position 3454M 1. While pressing the needle up/down key (1), turn on the power switch. 2. "n.0 xx" will appear in the main display (2). ("xx" is the setting value for the needle up stop position, and "0" is the default setting.) 3. Press the or key (3) to change the setting value for the needle up stop position. • If you press the key, the setting value will increase up to 10 and the needle up stop position will become lower. • If you press the key, the setting value will decrease down to -10 and the needle up stop position will become higher. 4. Press the ENTER key (4) for two seconds or more. A long buzzer will sound and the main display (2) will change to stitch number display mode. (This completes the needle up stop position setting.) * A setting value of "10" corresponds to an angle of rotation of approximately 10° for the upper shaft. Becomes higher NOTE: If the needle bar is not at the needle up stop position, "UP" will be displayed. Becomes lower 2138M 2139M 3455M 41 Z-8550A, 8560A

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
Z-8550A, 8560A
7. USING THE OPERATION PANEL (ADVANCED OPERATIONS)
41
7-2. Adjusting the needle up stop position
1. While pressing the needle up/down key (1), turn on the
power switch.
2. “n.0 xx” will appear in the main display (2).
(“xx” is the setting value for the needle up stop position,
and “0” is the default setting.)
3. Press the
or
key (3) to change the setting value
for the needle up stop position.
•
If you press the
key, the setting value will increase
up to 10 and the needle up stop position will become
lower.
•
If you press the
key, the setting value will decrease
down to -10 and the needle up stop position will become
higher.
4. Press the ENTER key (4) for two seconds or more.
A long buzzer will sound and the main display (2) will
change to stitch number display mode. (This completes
the needle up stop position setting.)
*
A setting value of “10” corresponds to an angle of rotation
of approximately 10
°
for the upper shaft.
NOTE:
If the needle bar is not at the needle up stop position,
“UP” will be displayed.
2138M
2139M
3454M
3455M
Becomes
higher
Becomes
lower