Brother International Z-8550A Instruction Manual - English - Page 80

<Installation&gt, adjustment in Adjusting the presser foot height. Refer

Get Brother International Z-8550A PDF manuals and user guides View all Brother International Z-8550A manuals
Add to My Manuals
Save this manual to your list of manuals

Page 80 highlights

3548M 13. OPTIONAL PARTS 1. Pass presser bar U (15) through the bushing (16) from above. 2. Use a spanner or similar tool to securely tighten presser bar tip A (17) or presser bar tip B (18) into presser bar U (15). 3. Fit the guide bracket (13) into presser bar U (15) and the groove (A) in the arm, and provisionally secure it in place with the screw (12). 4. Install the presser foot to presser bar tip A (17) or presser bar tip B (18). 5. Install the washer (11), spring guide (9) and spring (10). 6. Tighten the adjustment screw (8). 7. Loosen the screw (12) , align the presser foot with the groove in the needle plate (20), and then carry out the adjustment in "Adjusting the presser foot height". (Refer to P. 62.) * When tightening the screw (12), lower the guide bracket (13) until it is touching the lifter lever (19), and then tighten the screw (12). 8. Install the face plate (6) with the screws (4) and the screw (5). 9. Install the thread take-up guard (3) with the screws (2). 3549M Aligned 3550M Z-8550A, 8560A 72

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
Z-8550A, 8560A
13. OPTIONAL PARTS
72
<Installation>
1. Pass presser bar U (15) through the bushing (16) from
above.
2. Use a spanner or similar tool to securely tighten presser
bar tip A (17) or presser bar tip B (18) into presser bar U
(15).
3. Fit the guide bracket (13) into presser bar U (15) and the
groove (A) in the arm, and provisionally secure it in place
with the screw (12).
4. Install the presser foot to presser bar tip A (17) or presser
bar tip B (18).
5. Install the washer (11), spring guide (9) and spring (10).
6. Tighten the adjustment screw (8).
7. Loosen the screw (12) , align the presser foot with the
groove in the needle plate (20), and then carry out the
adjustment in “Adjusting the presser foot height”. (Refer
to P. 62.)
* When tightening the screw (12), lower the guide
bracket (13) until it is touching the lifter lever (19), and
then tighten the screw (12).
8. Install the face plate (6) with the screws (4) and the
screw (5).
9. Install the thread take-up guard (3) with the screws (2).
3548M
3549M
3550M
Aligned