Brother International Z-8550A Instruction Manual - English - Page 71

Adjusting the feed dog angle, 12-7. Adjusting the forward/back position of the feed dog

Get Brother International Z-8550A PDF manuals and user guides View all Brother International Z-8550A manuals
Add to My Manuals
Save this manual to your list of manuals

Page 71 highlights

12. STANDARD ADJUSTMENTS 12-6. Adjusting the feed dog angle 3517M standard (front) Lower the front The standard angle for the feed dog (1) is for the top of the needle plate to be parallel with the top of the feed dog (1) (for the 8550A) or raised slightly at the side closest to the operator (for the 8560A) when the feed dog (1) is raised to its highest position above the needle plate. (with the O mark on the feed bracket shaft (2) aligned with the mark on the feed rocker bracket arm (3)). 1. Turn the machine pulley to move the feed dog (1) its highest position above the needle plate. 2. Tilt back the machine head. 3. Loosen the set screw (4). 4. Turn the feed bracket shaft (2) in the direction of the arrow within a range of 90º with respect to the standard position. • In order to prevent puckering, lower the front of the feed dog (1). (Figure A) • In order to prevent the material from slipping, raise the front of the feed dog (1). (Figure B) 5. Securely tighten the set screws (4). * When the angle of the feed dog (1) is adjusted, the height and forward/back position of the feed dog (1) will also change and will need to be readjusted. Raise the front 3518M 12-7. Adjusting the forward/back position of the feed dog 3519M The clearance between the feed dog (1) and the needle plate should be the same at the front and back of the feed dog (1) when the feed dog (1) is moved to its furthest forward and furthest back positions by turning the machine pulley. 1. Tilt back the machine head. 2. Loosen the two screws (2). 3. Turn the feed rocker bracket arm (3) to adjust the forward/back position of the feed dog (1). 4. Securely tighten the two screws (2). 3520M 63 Z-8550A, 8560A

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
Z-8550A, 8560A
12. STANDARD ADJUSTMENTS
63
12-6. Adjusting the feed dog angle
The standard angle for the feed dog (1) is for the top of the
needle plate to be parallel with the top of the feed dog (1)
(for the 8550A) or raised slightly at the side closest to the
operator (for the 8560A) when the feed dog (1) is raised to
its highest position above the needle plate. (with the O mark
on the feed bracket shaft (2) aligned with the mark on the
feed rocker bracket arm (3)).
1. Turn the machine pulley to move the feed dog (1) its
highest position above the needle plate.
2. Tilt back the machine head.
3. Loosen the set screw (4).
4. Turn the feed bracket shaft (2) in the direction of the
arrow within a range of 90º with respect to the standard
position.
•
In order to prevent puckering, lower the front of the
feed dog (1). (Figure A)
•
In order to prevent the material from slipping, raise
the front of the feed dog (1). (Figure B)
5. Securely tighten the set screws (4).
*
When the angle of the feed dog (1) is adjusted, the height
and forward/back position of the feed dog (1) will also
change and will need to be readjusted.
12-7. Adjusting the forward/back position of the feed dog
The clearance between the feed dog (1) and the needle
plate should be the same at the front and back of the feed
dog (1) when the feed dog (1) is moved to its furthest
forward and furthest back positions by turning the machine
pulley.
1. Tilt back the machine head.
2. Loosen the two screws (2).
3. Turn the feed rocker bracket arm (3) to adjust the
forward/back position of the feed dog (1).
4. Securely tighten the two screws (2).
3518M
3517M
standard
Lower the front
Raise the front
(front)
3520M
3519M