Campbell Scientific 10525 ENC10/12, ENC12/14, ENC14/16, ENC16/18 Enclosures - Page 18

ENC10/12, and PWENC16/18, Enclosure brackets con d for a tower mount

Get Campbell Scientific 10525 PDF manuals and user guides View all Campbell Scientific 10525 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

ENC10/12, ENC10/12R, ENC12/14, ENC14/16, ENC16/18, PWENC12/14, PWENC14/16, and PWENC16/18 NOTE same three-piece brackets as the "-MM" option, except the pieces are rearranged so that the flanges are on the side of the bracket instead of in the middle. The distance between the centers of each flange needs to be 17" (see FIGURE 4-4, FIGURE 4-5, and FIGURE 4-6). Enclosures with the "-TM" option are shipped configured for the UT10 tower. Steps 1 through 3 of the following procedure are for configuring the bracket for attachment to a UT20 or UT30 tower. Attach the enclosure to a UT20 or UT30 tower as follows: 1. Remove the bolts and nuts connecting the bracket to the enclosure. 2. Slide out the flange sections so that the distance between the centers of each flange is 17" (see FIGURE 4-4). 3. Reattach the bracket to the enclosure using the original bolts and nuts. 4. Position the enclosure on the north side of the mast. 5. Place the enclosure at the desired height. Please note that the recommended lead lengths for our sensors assume the bottom of the enclosure is 3 ft from the ground. 6. Use the furnished 1.5" u-bolts to secure the enclosure to the tower legs. 7. Route the 14 AWG wire from the brass tower grounding clamp to the enclosure grounding lug. Strip one inch of insulation from each end of the wire and insert the end of the wire into the grounding lugs and tighten. D FIGURE 4-4. Enclosure brackets configured for a tower mount 12

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
ENC10/12, ENC10/12R, ENC12/14, ENC14/16, ENC16/18, PWENC12/14, PWENC14/16, and PWENC16/18
same three-piece brackets as the “-MM” option, except the pieces are
rearranged so that the flanges are on the side of the bracket instead of in the
middle.
The distance between the centers of each flange needs to be 17" (see
FIGURE 4-4, FIGURE 4-5, and FIGURE 4-6).
Enclosures with the “-TM” option are shipped configured for the
UT10 tower.
Steps 1 through 3 of the following procedure are
for configuring the bracket for attachment to a UT20 or UT30
tower.
NOTE
Attach the enclosure to a UT20 or UT30 tower as follows:
1.
Remove the bolts and nuts connecting the bracket to the enclosure.
2.
Slide out the flange sections so that the distance between the centers of
each flange is 17" (see FIGURE 4-4).
3.
Reattach the bracket to the enclosure using the original bolts and nuts.
4.
Position the enclosure on the north side of the mast.
5.
Place the enclosure at the desired height.
Please note that the
recommended lead lengths for our sensors assume the bottom of the
enclosure is 3 ft from the ground.
6.
Use the furnished 1.5" u-bolts to secure the enclosure to the tower legs.
7.
Route the 14 AWG wire from the brass tower grounding clamp to the
enclosure grounding lug.
Strip one inch of insulation from each end of
the wire and insert the end of the wire into the grounding lugs and tighten.
D
FIGURE 4-4.
Enclosure brackets configured for a tower mount
12