Campbell Scientific 10525 ENC10/12, ENC12/14, ENC14/16, ENC16/18 Enclosures - Page 20

Tripod Leg Base, of a CM106, CM106K, CM110, or CM120 tripod.

Get Campbell Scientific 10525 PDF manuals and user guides View all Campbell Scientific 10525 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

ENC10/12, ENC10/12R, ENC12/14, ENC14/16, ENC16/18, PWENC12/14, PWENC14/16, and PWENC16/18 4.4 Tripod Leg Base The "-LM" mount option is intended for attaching an enclosure to the leg base of a CM106, CM106K, CM110, CM115, or CM120 tripod. NOTE The ENC16/18 can be mounted to the leg base of a CM106 or CM106K only. An enclosure ordered with this option will be shipped with a bracket attached to each side of the enclosure and a u-bolt bracket. A 19124 bracket must also be attached to some tripods (see FIGURE 4-7). NOTE For tripods requiring 19124 bracket, the bracket may not be preinstalled on the tripod at the factory. In this situation, the 19124 bracket and mounting hardware will be shipped with the tripod and will need to be installed as shown in FIGURE 4-7. The CM106 and CM106K tripods have flanges built into the body of the tripod and do not require the 19124 bracket. Attach the enclosure to the leg base as follows: 1. Slide the keyhole notches in the upper and lower corners of the -LM bracket over the two extended Phillips head screws located on the tripod. The CM106 and CM106K have hooks extending from the tripod body in place of the Phillips screws. 2. Place the flange of the tripod's bracket into a notch in one of the enclosure's brackets (see FIGURE 4-7, FIGURE 4-8, and FIGURE 4-10). 3. Attach the u-bolt bracket on the other enclosure bracket (see FIGURE 4-9). 4. Use the furnished 2.5" u-bolt to secure the enclosure bracket to a tripod leg (see FIGURE 4-9 and FIGURE 4-10). The CM106K requires a usersupplied 5/16-18 x 1.5000" u-bolt due to the tripod's smaller leg size. 5. Route the 14 AWG wire from the brass tripod grounding clamp to the enclosure grounding lug. Strip one inch of insulation from each end of the wire and insert the end of the wire into the grounding lugs and tighten. 14

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
ENC10/12, ENC10/12R, ENC12/14, ENC14/16, ENC16/18, PWENC12/14, PWENC14/16, and PWENC16/18
4.4
Tripod Leg Base
The “-LM” mount option is intended for attaching an enclosure to the leg base
of a CM106, CM106K, CM110, CM115, or CM120 tripod.
The ENC16/18 can be mounted to the leg base of a CM106 or
CM106K only.
NOTE
An enclosure ordered with this option will be shipped with a bracket attached
to each side of the enclosure and a u-bolt bracket.
A 19124 bracket must also
be attached to some tripods (see FIGURE 4-7).
For tripods requiring 19124 bracket, the bracket may not be pre-
installed on the tripod at the factory.
In this situation, the 19124
bracket and mounting hardware will be shipped with the tripod
and will need to be installed as shown in FIGURE 4-7.
NOTE
The CM106 and CM106K tripods have flanges built into the
body of the tripod and do not require the 19124 bracket.
Attach the enclosure to the leg base as follows:
1.
Slide the keyhole notches in the upper and lower corners of the –LM
bracket over the two extended Phillips head screws located on the tripod.
The CM106 and CM106K have hooks extending from the tripod body in
place of the Phillips screws.
2.
Place the flange of the tripod’s bracket into a notch in one of the
enclosure’s brackets (see FIGURE 4-7, FIGURE 4-8, and FIGURE 4-10).
3.
Attach the u-bolt bracket on the other enclosure bracket (see FIGURE
4-9).
4.
Use the furnished 2.5" u-bolt to secure the enclosure bracket to a tripod leg
(see FIGURE 4-9 and FIGURE 4-10).
The CM106K requires a user-
supplied 5/16-18 x 1.5000" u-bolt due to the tripod’s smaller leg size.
5.
Route the 14 AWG wire from the brass tripod grounding clamp to the
enclosure grounding lug.
Strip one inch of insulation from each end of the
wire and insert the end of the wire into the grounding lugs and tighten.
14