Canon HV30E Instruction Manual - Page 29

Returning to a Pre-marked Position, If you marked the zero memory

Get Canon HV30E PDF manuals and user guides View all Canon HV30E manuals
Add to My Manuals
Save this manual to your list of manuals

Page 29 highlights

Playback 29 Basic Functions 6 Press FUNC. . appears. Note that if the joystick guide appears on the screen, it will conceal the icon. Press ( ) to hide the joystick guide. * In mode, select [ PLAY/ OUT SETUP] instead. TO ADJUST THE VOLUME OF THE HEADPHONES In mode, adjust the volume of the headphones with the [PHONES VOL.] setting ( 39). In mode, use the joystick and the joystick guide following the same procedure as when adjusting the speaker's volume. IMPORTANT Do not connect the headphones to the AV/ terminal if the icon does not appear on the screen. If you connect the headphones while the terminal is set to AV output only noise will be output. When using headphones, make sure to lower the volume to an appropriate level. The sound of the built-in speaker will be muted when you close the LCD panel, when you connect the stereo video cable to the AV/ terminal or when the AV/ terminal is set to [ PHONES]. NOTES Use commercially available headphones with a ∅ 3.5 mm minijack and a cable no longer than 3 m. When you turn off the camcorder, the [AV/PHONES] setting in mode will return to [ AV]. The volume of the headphones cannot be adjusted while recording. Returning to a Pre-marked Position If you wish to return to a particular scene later, mark the point with the zero set memory and the tape will stop at that point when you rewind/fast forward the tape. ( 8) 1 While recording or during playback, press ZERO SET MEMORY on the wireless controller at the point you wish to return to later. • The time code changes to "0:00:00 ". • Press ZERO SET MEMORY again to cancel the memory. 2 If you marked the zero memory while recording, set the camcorder to mode. If you marked the zero memory during playback, press . 3 Press to locate the zero mark. • If the tape counter shows a negative number, press instead. • appears and the camcorder rewinds/fast forwards the tape. • The tape stops at or near the zero mark, disappears and the correct time code will be displayed again. NOTES If there are blank sections between recordings or sections recorded in different standards (HDV/DV) on the same tape, the zero set memory may not work correctly.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
Playback
Basic Functions
29
6
Press
.
appears. Note that if the joystick
guide appears on the screen, it will
conceal the
icon. Press (
) to
hide the joystick guide.
* In
mode, select [
PLAY/
OUT SETUP] instead.
T
O
ADJUST
THE
VOLUME
OF
THE
HEADPHONES
In
mode, adjust the volume of
the headphones with the [PHONES VOL.]
setting (
39). In
mode, use
the joystick and the joystick guide
following the same procedure as when
adjusting the speaker’s volume.
IMPORTANT
°
Do not connect the headphones to the AV/
terminal if the
icon does not appear on the
screen. If you connect the headphones while
the terminal is set to AV output only noise will
be output.
°
When using headphones, make sure to lower
the volume to an appropriate level.
°
The sound of the built-in speaker will be
muted when you close the LCD panel, when
you connect the stereo video cable to the
AV/
terminal or when the AV/
terminal is
set to [
PHONES].
NOTES
°
Use commercially available headphones with
a
∅
3.5 mm minijack and a cable no longer than
3 m.
°
When you turn off the camcorder, the
[AV/PHONES] setting in
mode will
return to [
AV].
°
The volume of the headphones cannot be
adjusted while recording.
Returning to a Pre-marked Position
If you wish to return to a particular scene
later, mark the point with the zero set
memory and the tape will stop at that
point when you rewind/fast forward the
tape.
1
While recording or during playback,
press
on the
wireless controller at the point you
wish to return to later.
• The time code changes to
“0:00:00
”.
• Press
again to
cancel the memory.
2
If you marked the zero memory
while recording, set the camcorder
to
mode. If you marked
the zero memory during playback,
press
.
3
Press
to locate the zero mark.
• If the tape counter shows a negative
number, press
instead.
•
appears and the camcorder
rewinds/fast forwards the tape.
• The tape stops at or near the zero
mark,
disappears and the correct
time code will be displayed again.
NOTES
If there are blank sections between recordings
or sections recorded in different standards
(HDV/DV) on the same tape, the zero set
memory may not work correctly.
FUNC.
(
8)
ZERO SET MEMORY
ZERO SET MEMORY