Canon MP970 MP970 series Quick Start Guide - Page 40

Photo Printing from Printed Photo or Film, Lift the Document Cover - parts

Page 40 highlights

4 Lift the Document Cover, remove the FAU Protective Sheet from the Document Cover, and then remove the Film Guide (A) from the rear of the FAU Protective Sheet. (A) (A) Film Guide 5 Mount film in the Film Guide and load it on the Platen Glass. z Mounting a 35 mm Film Strip: (1) On the Film Guide (B), open the Film Holder (C). Squeeze the edges of the Film Holder inward lightly to release it. (D) (B) (C) Note Put your finger on the hinge part (D) of the Film Strip Frame (E) so that it does not come off the Film Guide when opening the Film (E) Holder. (2) Mount the film in the Film Strip Frame on the Film Guide with the front side (the side showing the correct image) facing down, and with the frame order running from left to right. Set the tip of the film under the tabs of the Film Strip Frame and position the film so that the (2) separation lines between frames are aligned with the white line marks of the Film Holder. Note Depending on the films, the separation lines between frames may not be aligned with the white line marks of the Film Holder when you set the tip of the film under the tabs of the Film Strip Frame. In this case, give priority to (3) aligning the separation lines between frames with the white line marks. (3) Squeeze the edges of the Film Holder inward lightly and close it completely. 36 Photo Printing from Printed Photo or Film

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120

36
Photo Printing from Printed Photo or Film
4
Lift the Document Cover, remove the FAU Protective Sheet from the Document
Cover, and then remove the Film Guide (A) from the rear of the FAU Protective
Sheet.
5
Mount film in the Film Guide and load it on the Platen Glass.
Mounting a 35 mm Film Strip:
(1)
On the Film Guide (B), open the Film Holder
(C).
Squeeze the edges of the Film Holder inward
lightly to release it.
(2)
Mount the film in the Film Strip Frame on the
Film Guide with the front side (the side
showing the correct image) facing down, and
with the frame order running from left to right.
Set the tip of the film under the tabs of the Film
Strip Frame and position the film so that the
separation lines between frames are aligned
with the white line marks of the Film Holder.
(3)
Squeeze the edges of the Film Holder inward
lightly and close it completely.
Note
Put your finger on the hinge part (D) of the
Film Strip Frame (E) so that it does not come
off the Film Guide when opening the Film
Holder.
Note
Depending on the films, the separation lines
between frames may not be aligned with the
white line marks of the Film Holder when you
set the tip of the film under the tabs of the Film
Strip Frame. In this case, give priority to
aligning the separation lines between frames
with the white line marks.
(A)
(A) Film Guide
(E)
(B)
(C)
(D)
(2)
(3)