Home » Canon Manuals » Projectors » Canon REALiS LCOS WUX500ST » Manual Viewer

Canon REALiS LCOS WUX500ST WUX500ST Users Manual - Page 124

AMX Device Discovery settings, Crestron RoomView settings

View all Canon REALiS LCOS WUX500ST manuals

Add to My Manuals
Save this manual to your list of manuals

Page 124 highlights

Menu Description Menu Network setting initialization Function The following network settings are initialized. Settings configured from the projector menu • Network settings lock (P121) • Network password setting (P121) • Register network password (P121) • Network standby settings (P122) • Network (wired/wireless) (P122) • Detailed settings (wired) (P123) - IP address (wired) (P123) - Gateway address (wired) (P123) - DHCP (wired) (P123) - Subnet mask (wired) (P123) • PJLink (P128) • AMX Device Discovery settings (P129) • Crestron RoomView settings (P129) • IP addresses of destination projectors configured for PC-free multi projection Settings configured from the web screen • [Password] (P137) • [Wired] (P138) - DHCP (P138) - IP address (P138) - Subnet mask (P138) - Default gateway (P138) • [NMPJ Password] (P140) • [Mail] (P141) • [Mail auth] (P142) • [SNMP] (P143) • [Projector info.] (P144) If the IP address (wired) is set to "192.168.253.254" when initialization is carried out, the IP address (wired) will be initialized to "192.168.254.253". 124

Section	Page
How to Use This Manual	2
Table of Contents	3
Projector Highlights	5
Safety Instructions	7
Safety Precautions	8
Precautions for Use	14
Installation and Handling Precautions	16
Precautions on the Lamp	17
Precautions for the Batteries of the Remote Control	18
For Safe Use	20
Before Installation	21
Precautions When Carrying/Shipping the Projector	21
Precautions for Installation	21
When Using Mounted on the Ceiling	23
Install Facing in the Correct Direction	24
Open Source Software	26
Software under the GNU General Public License Version 2	26
Before Use	27
Included Accessories	27
Attaching the Lens Cap	27
Part Names	28
Projector	28
Front Side	28
Rear Side	28
Projection Lens	29
Side Control	29
LED Indicators	30
LED Indicator Displays	31
Input Terminal	32
Remote Control	33
Preparing the Remote Control	35
Installing Remote Control Batteries	35
Remote Control Operating Range	36
Using an Optional Wired Remote (RS-RC05)	36
Basic Guide	37
Installation Procedure	38
Setting Up the Projector	38
Positioning the Projector in Front of the Screen	38
Floor Installation	38
Installation Tilted Upward	39
Installation on High Surfaces	39
Ceiling Mounting or Rear Projection	40
Relationship between Projecting Distance and Image Size	41
Lens Shift Function	41
Amount of Lens Shift	41
Connection Procedure	43
Connecting a Computer	43
Connecting AV Equipment	45
Plugging the Projector In	46
Projection Procedure	47
Step 1 Turn the Projector On	47
When the Language Selection Screen Appears	48
When the Password Input Screen Appears	48
When “No signal” Appears	48
When Notebook Computer Screen Does Not Appear	48
Adjusting Image	48
Changing Notebook Computer Screen Output	49
Turning on External Monitor Output	49
Step 2 Select an Input Signal	50
Step 3 Adjust the Image	51
Setting the Display Resolution of the Computer	51
Windows 10	51
Windows 8.1 / Windows 8	51
Windows 7	51
Windows Vista	52
Mac OS X	52
Auto PC Adjustment	52
Focusing, Resizing, or Moving the Image	53
Adjusting Image Focus	53
Adjusting the Image Position	53
Step 4 Select an Aspect Ratio (Screen Aspect) Matching the Screen	54
Selecting Screen Aspect	54
Select the Aspect	56
Types of Aspect Ratios	56
Selecting an Aspect Ratio	57
Step 5 Adjusting Keystone Distortion	58
Horizontal/Vertical Keystone Correction	58
Corner Adjustment	59
Resetting the Keystone Adjustment	60
Step 6 Select the Image Quality (Image Mode)	61
Image Modes	61
Selecting an Image Mode	62
Step 7 Turn the Projector Off	62
Convenient Features	63
Temporarily Blacking Out an Image	63
Freezing the Picture	63
Projecting Images Stored on a USB Flash Drive	63
Projecting a Test Pattern from the Menu	64
Set Power-Saving Settings	64
Setting Up Power-Saving Features	64
Advanced Guide	65
Using Menus	66
Menu Configuration	66
Basic Menu Operations	67
Menu Configuration	69
Menu Description	79
Input settings	79
Aspect	80
Auto PC	80
Input signal select	80
Input signal settings	81
Input level	82
Color space	82
Over scan	82
Progressive	83
Slideshow interval	83
Animation effect	83
PC-free multi projection	84
Mode setting	84
Layout pattern setting	84
Destination projector setting	84
Slideshow interval	85
Animation effect	85
Split screen	85
Image adjustment	86
Image mode	87
Create profile	87
Brightness	88
Contrast	88
Sharpness	88
Gamma	88
Color adjustment	88
Advanced adjustment	89
Ambient light	89
Random noise reduction	89
MPEG noise reduction	90
Mosquito noise reduction	90
Dynamic gamma	90
Mem. color correct	90
6-axis color adjust	91
Fine-Tune Gamma	91
Lamp mode	92
Reset	92
Image priority	92
Install settings	93
Positional lock	94
Image flip H/V	94
Screen aspect	94
Zoom	95
Keystone	95
Digital image shift	96
Professional settings	96
Micro-digital image shift	96
Registration	96
Fan mode	96
Vertical projection	97
Edge blending	97
Screen color	100
On screen	100
Menu position	101
Guide	101
Show input status	101
Overheat warning display	101
Menu display time	101
Lamp warning display	102
Air filter warning display	102
Split screen ID display	102
Test pattern	102
System settings	103
User screen settings	104
Logo capture	104
Logo position	104
No signal screen	104
Screen when blank	104
Projector on	105
Interface settings	105
Key repeat	105
Key lock	105
Remote control channel	106
Audio in terminal select	106
HDBaseT	107
Communication settings	107
HDMI image input	108
HDBaseT image input	108
Power management mode	108
Power management duration	109
Direct power on	109
Beep	109
Motion blur reduction	110
Language	110
Other settings	111
Password settings	111
Register password	112
[Fn] button settings	112
Gamma restore	112
Lamp counter	112
Air filter counter	113
Power counter	113
Firmware	113
Factory defaults	113
Network settings	114
Network Connection Overview	114
Connection Methods	114
Wired Networks	114
Wireless Networks	115
Wireless LAN (Wi-Fi)	118
Countries and Regions Where Wireless LAN Use Is Permitted	118
Model Number	118
FCC/IC NOTICE	118
Model: WUX500ST (including WLAN Module Model ZC-ST, FCC ID: AZD220)	118
Completing Projector Settings	120
Network settings lock	121
Network password setting	121
Register network password	121
Network standby settings	122
Network (wired/wireless)	122
Detailed settings (wired)	123
Detailed settings (wireless)	125
PJLink	128
AMX Device Discovery	129
Crestron RoomView	129
Information	129
Completing Computer Settings	130
Specifying an IP Address	130
Windows 10	130
Windows 8.1 / Windows 8	131
Windows 7	132
Windows Vista	132
Mac OS X	133
Resetting the IP Address Setting of the Computer	133
Setting Up the Network	133
Displaying the Network Configuration Screen	133
Network Setting	135
Error Notification Mails	148
Controlling the Projector from a Computer	149
Checking Projector Information	151
Advanced Projection	153
Projecting Images on a USB Flash Drive	153
Description of USB File Browser	155
Selecting an Image for Projection	156
Selecting a Drive	156
Selecting a Folder	156
Selecting an Image File for Projection	156
Changing the View	156
Operating the Projected Image	156
Running a Slideshow of Data Saved in a USB Flash Memory	157
Creating an Image File Folder	157
Setting a Slideshow Interval	157
Using PC-Free Multi Projection	158
Preparing for Projection	158
Split-Screen Display	161
Projecting from Multiple Projectors at Once (Edge Blending)	163
Basic Instructions	163
Color Adjustment	164
Black Level Adjustment	164
Smoother Overlapping Areas	165
Corner Adjustment	166
Other Information	169
Maintenance	170
Cleaning the Projector	170
Cleaning the Air Filter	171
Replacing the Air Filter	173
Replacing the Lamp	174
Replacement Lamp	175
Lamp Replacement Procedure	176
If the Lamp Cover Comes Off	178
Product Specifications	179
Relationship between Aspect and Screen Aspect	179
When projecting at the original aspect ratio on a 16:10 screen	179
When projecting at the original aspect ratio on a 16:9 screen	180
When projecting at the original aspect ratio on a 4:3 screen	180
When projecting to fill a 16:10 screen	181
When projecting to fill a 16:9 screen	181
When projecting to fill a 4:3 screen	182
Displayed Test Patterns	183
Supported Signal Types	184
Projector	186
Remote Control	187
External View	188
ANALOG PC-2 / COMPONENT Terminal	189
Service Port (CONTROL)	189
Troubleshooting	192
LED Indicator Details	192
Symptoms and Solutions	193
You Cannot Turn on the Projector	193
You Cannot Project an Image from the Projector	194
There is no Sound	195
The Projected Image Is Blurred	195
You Cannot Project an Image Appropriately	196
The Projector Power Turns Off	196
The Projector Cannot Join the Network	197
You Cannot Operate the Remote Control	198
Index	199
Numerics	199
A	199
B	199
C	199
D	199
E	199
F	199
G	199
H	199
I	199
K	199
L	199
M	200
N	200
O	200
P	200
R	200
S	200
T	200
U	200
W	200

Match case Limit results 1 per page

Menu Description

124

Network setting

initialization

The following network settings are initialized.

Settings configured from the projector menu

•

Network settings lock (

P121

)

•

Network password setting (

P121

)

•

P121

)

•

Network standby settings (

P122

)

•

Network (wired/wireless) (

P122

)

•

Detailed settings (wired) (

P123

)

IP address (wired) (

P123

)

Gateway address (wired) (

P123

)

DHCP (wired) (

P123

)

Subnet mask (wired) (

P123

)

•

PJLink (

P128

)

•

AMX Device Discovery settings (

P129

)

•

Crestron RoomView settings (

P129

)

•

IP addresses of destination projectors configured for PC-free multi

projection

Settings configured from the web screen

•

[Password] (

P137

)

•

[Wired] (

P138

)

DHCP (

P138

)

IP address (

P138

)

Subnet mask (

P138

)

Default gateway (

P138

)

•

[NMPJ Password] (

P140

)

•

[Mail] (

P141

)

•

[Mail auth] (

P142

)

•

[SNMP] (

P143

)

•

[Projector info.] (

P144

)

Function

If the IP address (wired) is set to “192.168.253.254” when

initialization is carried out, the IP address (wired) will be

initialized to “192.168.254.253”.