Home » Cisco Manuals » Hubs & Switches » Cisco 6509E » Manual Viewer

Cisco 6509E Supervisor Guide - Page 60

Table 2-20, Supervisor Engine 720-10GE Front Panel Status LEDs continued

Add to My Manuals
Save this manual to your list of manuals

Page 60 highlights

Supervisor Engine 720-10GE Chapter 2 Supervisor Engines Table 2-20 LED DISK 0 LINK Supervisor Engine 720-10GE Front Panel Status LEDs (continued) Color and Meaning This LED is illuminated green when the installed Flash PC card is being accessed and is performing either a read operation or a write operation. Each uplink port has a LINK LED associated with it. The LINK LED indicates the link status of the corresponding port. • Green-The port is active (the link is connected and operational). • Flashing orange-The port failed diagnostics and is disabled. • Orange-The port is disabled. • Red-The supervisor engine is resetting; an overtemperature condition has occurred. Note If the supervisor engine fails to download code and configuration information successfully during the initial reset, the LED stays red; the supervisor engine does not come online. • Off-The port is not active or the link is not connected. 2-32 Catalyst 6500 Series Supervisor Engine Guide OL-7397-03

Section	Page
Catalyst 6500 Series Supervisor Engine Guide	1
Contents	3
Preface	5
Audience	5
Organization	5
Conventions	6
Statement 1071-Warning Definition	7
Related Documentation	13
Catalyst 6500 Series Switch Chassis Overview	15
Catalyst 6503 Switch	15
Catalyst 6503-E	16
Catalyst 6504-E	17
Catalyst 6506	18
Catalyst 6506-E	19
Catalyst 6509	20
Catalyst 6509-E	21
Catalyst 6509-NEB	22
Catalyst 6509-NEB-A	23
Catalyst 6509-V-E	24
Catalyst 6513	25
Catalyst 6513-E	26
Supervisor Engines	29
Supervisor Engine 2	29
Supervisor Engine 32	35
Supervisor Engine 32 PISA	42
Supervisor Engine 720	49
Supervisor Engine 720-10GE	54
Supervisor Engine 2T	61
Installing Supervisor Engines	69
Safety	69
Required Tools	70
Installing a Supervisor Engine	70
Removing a Supervisor Engine	78
USB Console Port Driver Installation	81
Installing the Cisco Microsoft Windows USB Device Driver	81
Installing the Cisco Microsoft Windows XP USB Driver	82
Installing the Cisco Microsoft Windows 2000 USB Driver	82
Installing the Cisco Microsoft Windows Vista and Windows 7 USB Driver	83
Uninstalling the Cisco Microsoft Windows USB Driver	83
Uninstalling the Cisco Microsoft Windows XP and 2000 USB Driver	83
Using the Add or Remove Programs utility	83
Using the Setup.exe program	84
Uninstalling the Cisco Microsoft Windows Vista and Windows 7 USB Driver	84
Installing Pluggable Transceivers	85
Attaching the Network Interface Cables	85
Attaching Optical Network Interface Cables	86
Mode-Conditioning Patch Cord	86
Connecting Transceivers to a Copper Network	90
Where to Go Next	90
Pluggable Transceivers	91
B	93
Port, Cable, and Connector Specifications	93
Console Port	93
Console Port Cables and Adapters	93
Figure B-1 Identifying a Rollover Cable	94
CONSOLE PORT MODE Switch (Supervisor Engine 2 Only)	94
Console Port Mode 1 Signaling and Pinouts	95
DB-9 Adapter (for Connecting to a PC)	95
Table B-1 Port Mode 1: Console Port Signaling and Pinouts (DB-9 Adapter)	95
DB-25 Adapter (for Connecting to a Terminal)	96
Table B-2 Port Mode 1: Console Port Signaling and Pinouts (DB-25 Adapter)	96
Modem Adapter	96
Table B-3 Port Mode 1: Console Port Signaling and Pinouts (Modem Adapter)	96
Console Port Mode 2 Signaling and Pinouts	97
Table B-4 Console Port Pinouts (Port Mode Switch Out)	97
Uplink Ports	97
Table B-5 Supervisor Engine Uplink Ports	97
Table B-6 Cabling Guidelines for Transceivers	98
USB Ports	99
Copper and Fiber-Optic Connectors	99
RJ-45 Connector	99
Figure B-2 RJ-45 Interface Cable Connector	100
Fiber-Optic Connectors	100
SC Connectors	100
Figure B-3 SC Optical Connector	100
LC Connectors	101
Figure B-4 LC Fiber-Optic Connector	101
ESD Precautions	103
Attaching Your ESD Grounding Strap	103