Cisco 6509E Supervisor Guide - Page 97

Console Port Mode 2 Signaling and Pinouts, Table B-4 Console Port Pinouts (Port Mode Switch Out)

Get Cisco 6509E - Catalyst Switch PDF manuals and user guides View all Cisco 6509E manuals
Add to My Manuals
Save this manual to your list of manuals

Page 97 highlights

Appendix B Port, Cable, and Connector Specifications Uplink Ports Console Port Mode 2 Signaling and Pinouts This section provides the signaling and pinouts for the console port in mode 2 (CONSOLE PORT MODE switch in the out position). See Table B-4 for the pinouts. Table B-4 Console Port Pinouts (Port Mode Switch Out) Console Port Pin (signal) 1 (RTS)1 2 (DTR) 3 (RxD) 4 (GND) 5 (GND) 6 (TxD) 7 (DSR) 8 (CTS)1 1. Pin 1 is connected internally to Pin 8. Console Device Input/Output Output Output Input GND GND Output Input Input Uplink Ports The Supervisor Engine 2, Supervisor Engine 32, Supervisor Engine 32 PISA, the Supervisor Engine 720, Supervisor Engine 720-10GE, and the Supervisor Engine 2T all have Ethernet uplink ports available on the front panel. These Ethernet ports can be used to provide additional port capacity for a fully configured switch or can reduce the need to use a chassis slot for a Gigabit Ethernet module or 10-Gigabit Ethernet module where only a few Gigabit or 10-Gigabit Ethernet ports are required. Table B-5 lists the supervisor engine model and the number and type of uplink ports available. Table B-5 Supervisor Engine Uplink Ports Supervisor Engine Supervisor Engine 2 Supervisor Engine 32 (WS-SUP32-GE-3B and WS-SUP32P-GE) Supervisor Engine 32 (WS-SUP32-10GE-3B and WS-SUP32P-10GE) Number of Uplink Ports 2 9 3 Type of Uplink Port Two 1000BASE-X ports (The two ports require GBIC transceivers.) • Eight 1000BASE-X ports (The eight ports require SFP transceivers.) • One 10/100/1000 RJ-45 port (The port does not require a pluggable transceiver.) • Two 10-GBASE-X (The two ports require XENPAK transceivers) • One 10/100/1000 RJ-45 port (The port does not require a pluggable transceiver) OL-7397-03 Catalyst 6500 Series Supervisor Engine Guide B-5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
B-5
Catalyst 6500 Series Supervisor Engine Guide
OL-7397-03
Appendix B
Port, Cable, and Connector Specifications
Uplink Ports
Console Port Mode 2 Signaling and Pinouts
This section provides the signaling and pinouts for the console port in mode 2 (CONSOLE PORT MODE
switch in the
out
position). See
Table B-4
for the pinouts.
Uplink Ports
The Supervisor Engine 2, Supervisor Engine 32, Supervisor Engine 32 PISA, the Supervisor
Engine 720, Supervisor Engine 720-10GE, and the Supervisor Engine 2T all have Ethernet uplink ports
available on the front panel. These Ethernet ports can be used to provide additional port capacity for a
fully configured switch or can reduce the need to use a chassis slot for a Gigabit Ethernet module or
10-Gigabit Ethernet module where only a few Gigabit or 10-Gigabit Ethernet ports are required.
Table B-5
lists the supervisor engine model and the number and type of uplink ports available.
Table B-4
Console Port Pinouts (Port Mode Switch Out)
Console Port
Console Device
Pin (signal)
Input/Output
1 (RTS)
1
1.
Pin 1 is connected internally to Pin 8.
Output
2 (DTR)
Output
3 (RxD)
Input
4 (GND)
GND
5 (GND)
GND
6 (TxD)
Output
7 (DSR)
Input
8 (CTS)
1
Input
Table B-5
Supervisor Engine Uplink Ports
Supervisor Engine
Number of
Uplink Ports
Type of Uplink Port
Supervisor Engine 2
2
Two 1000BASE-X ports
(The two ports require GBIC transceivers.)
Supervisor Engine 32
(WS-SUP32-GE-3B and
WS-SUP32P-GE)
9
•
Eight 1000BASE-X ports (The eight ports
require SFP transceivers.)
•
One 10/100/1000 RJ-45 port (The port does
not require a pluggable transceiver.)
Supervisor Engine 32
(WS-SUP32-10GE-3B and
WS-SUP32P-10GE)
3
•
Two 10-GBASE-X (The two ports require
XENPAK transceivers)
•
One 10/100/1000 RJ-45 port (The port does
not require a pluggable transceiver)