Cisco 6509E Supervisor Guide - Page 69

Installing Supervisor Engines, Safety

Get Cisco 6509E - Catalyst Switch PDF manuals and user guides View all Cisco 6509E manuals
Add to My Manuals
Save this manual to your list of manuals

Page 69 highlights

3 C H A P T E R Installing Supervisor Engines Revised: July 2011 This chapter describes how to safely install and remove supervisor engines modules in the Catalyst 6500 series switches, and it contains these sections: • Safety, page 3-1 • Required Tools, page 3-2 • Installing a Supervisor Engine, page 3-2 • Removing a Supervisor Engine, page 3-10 • Installing Pluggable Transceivers, page 3-17 • Attaching the Network Interface Cables, page 3-17 • Where to Go Next, page 3-22 Tip For additional information about Cisco Catalyst 6500 Series Switches (including configuration examples and troubleshooting information), see the documents listed on this page: http://www.cisco.com/en/US/products/hw/switches/ps708/tsd_products_support_series_home.html Safety Safety warnings appear throughout this publication in procedures that may harm you if performed incorrectly. A warning symbol precedes each warning statement. The warnings below are general warnings that are applicable to the entire publication. Warning Only trained and qualified personnel should be allowed to install, replace, or service this equipment. Statement 1030 Warning Before opening the unit, disconnect the telephone-network cables to avoid contact with telephone-network voltages. Statement 1041 OL-7397-03 Catalyst 6500 Series Supervisor Engine Guide 3-1

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
CHAPTER
3-1
Catalyst 6500 Series Supervisor Engine Guide
OL-7397-03
3
Installing Supervisor Engines
Revised: July 2011
This chapter describes how to safely install and remove supervisor engines modules in the Catalyst 6500
series switches, and it contains these sections:
•
Safety, page 3-1
•
Required Tools, page 3-2
•
Installing a Supervisor Engine, page 3-2
•
Removing a Supervisor Engine, page 3-10
•
Installing Pluggable Transceivers, page 3-17
•
Attaching the Network Interface Cables, page 3-17
•
Where to Go Next, page 3-22
Tip
For additional information about Cisco Catalyst 6500 Series Switches (including configuration examples
and troubleshooting information), see the documents listed on this page:
Safety
Safety warnings appear throughout this publication in procedures that may harm you if performed
incorrectly. A warning symbol precedes each warning statement. The warnings below are general
warnings that are applicable to the entire publication.
Warning
Only trained and qualified personnel should be allowed to install, replace, or service this equipment.
Statement 1030
Warning
Before opening the unit, disconnect the telephone-network cables to avoid contact with
telephone-network voltages.
Statement 1041