Compaq ProLiant 8500 ProLiant 8500 Servers Maintenance and Service Guide - Page 101

Array Drive Failure., The following SCSI

Get Compaq ProLiant 8500 PDF manuals and user guides View all Compaq ProLiant 8500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 101 highlights

Diagnostic Tools 3-23 Table 3-2 POST Error Messages continued Error Code Audible Beeps 1779-Slot X Drive None Array - Replacement drive(s) detected OR previously failed drive(s) now operational: Port Y: SCSI ID Z: Restore data from backup if replacement drive X has been installed. 1780-Disk 0 Failure None 1781-Disk 1 Failure None 1782-Disk Controller None Failure 1783-Slot X Drive None Array Controller Failure. 1784-Slot X Drive None Array Drive Failure. The following SCSI drive(s) should be replaced: SCSI Port Y: SCSI ID Z: Probable Source of Problem Intermittent drive failure or possible loss of data detected. Recommended Action If this message displays and drive X has not been replaced, there may be an intermittent drive failure. This message also displays immediately following drive replacement whenever data must be restored from backup. Hard drive/format error detected. Hard drive/format error detected. Hard disk drive circuitry error detected. ROM installation problem or array accelerator board problem detected. Defective drive and/or cables detected. Run Compaq Diagnostics. Replace failed assembly as indicated. Run Compaq Diagnostics. Replace failed assembly as indicated. Run Compaq Diagnostics. Replace failed assembly as indicated. If this message displays immediately following a ROM installation, if the ROM is defective or not installed properly. Check to see if the array accelerator board is attached properly. Check that the array controller is firmly inserted in its slot. Try upgrading the System ROM. Otherwise, replace the Smart Array Controller. Check for loose cables. Replace defective drive X and/or cable(s). continued

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
Diagnostic Tools
3-23
Table 3-2
POST Error Messages
continued
Error Code
Audible Beeps
Probable Source of Problem
Recommended Action
1779-Slot
X
Drive
Array
–
Replacement
drive(s) detected OR
previously failed
drive(s) now
operational:
Port
Y
: SCSI ID
Z
:
Restore data from
backup if
replacement drive
X
has been installed.
None
Intermittent drive failure or
possible loss of data detected.
If this message displays and
drive
X
has not been replaced,
there may be an intermittent
drive failure. This message also
displays immediately following
drive replacement whenever
data must be restored from
backup.
1780-Disk 0 Failure
None
Hard drive/format error detected.
Run Compaq Diagnostics.
Replace failed assembly as
indicated.
1781-Disk 1 Failure
None
Hard drive/format error detected.
Run Compaq Diagnostics.
Replace failed assembly as
indicated.
1782-Disk Controller
Failure
None
Hard disk drive circuitry error
detected.
Run Compaq Diagnostics.
Replace failed assembly as
indicated.
1783-Slot
X
Drive
Array Controller
Failure.
None
ROM installation problem or array
accelerator board problem
detected.
If this message displays
immediately following a ROM
installation, if the ROM is
defective or not installed
properly. Check to see if the
array accelerator board is
attached properly. Check that
the array controller is firmly
inserted in its slot. Try
upgrading the System ROM.
Otherwise, replace the Smart
Array Controller.
1784-Slot
X
Drive
Array Drive Failure.
The following SCSI
drive(s) should be
replaced:
SCSI Port
Y
:
SCSI ID
Z
:
None
Defective drive and/or cables
detected.
Check for loose cables. Replace
defective drive
X
and/or
cable(s).
continued