Compaq ProLiant 8500 ProLiant 8500 Servers Maintenance and Service Guide - Page 104

Error Code, Audible Beeps, Probable Source of Problem, Recommended Action, SCSI Port, SCSI ID Z

Get Compaq ProLiant 8500 PDF manuals and user guides View all Compaq ProLiant 8500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 104 highlights

3-26 Compaq ProLiant 8500 Server Maintenance and Service Guide Table 3-2 POST Error Messages continued Error Code Audible Beeps Probable Source of Problem Recommended Action *1788-Slot X Drive Array Reports Incorrect Drive Replacement. The following SCSI drive(s) should have been replaced: SCSI Port Y: SCSI ID Z The following SCSI drive(s) were incorrectly replaced: SCSI Port Y: SCSI ID Z. None Drives are not installed in their 1. Reinstall the drives original positions, so the drives correctly as indicated. have been disabled. 2. Press F1 to restart the computer with the drive array disabled. -Or- Press F2 to use the drives as configured and lose all the data on them. Select F1 to continue - drive array will remain disabled. Select F2 to reset configuration - all data will be lost. * The 1788 error message can also be displayed inadvertently due to a bad power cable connection to the drive, noise on the data cable, or a defective SCSI cable. If this message was due to a bad power cable connection, but not incorrect drive replacement, repair the connection and press F2. If the message is not eliminated by pressing F2, run Array Diagnostic Utility to resolve. -Or- If this message was not due to a bad power cable connection and no drive replacement took place, this could indicate noise on the data cable. Check cable for proper routing. -Or- If this message is due to a defective SCSI cable, replace the cable. continued

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
3-26
Compaq ProLiant 8500 Server Maintenance and Service Guide
Table 3-2
POST Error Messages
continued
Error Code
Audible Beeps
Probable Source of Problem
Recommended Action
*1788-Slot
X
Drive
Array Reports
Incorrect Drive
Replacement. The
following SCSI
drive(s) should have
been replaced: SCSI
Port
Y
: SCSI ID
Z
The following SCSI
drive(s) were
incorrectly replaced:
SCSI Port
Y
:
SCSI ID Z.
Select
F1
to continue
–
drive array will
remain disabled.
Select
F2
to reset
configuration
–
all
data will be lost.
None
Drives are not installed in their
original positions, so the drives
have been disabled.
1.
Reinstall the drives
correctly as indicated.
2.
Press
F1
to restart the
computer with the drive
array disabled.
-Or-
Press
F2
to use the drives
as configured and lose all
the data on them.
*
The 1788 error message can also be displayed inadvertently due to a bad power cable connection to the drive, noise
on the data cable, or a defective SCSI cable. If this message was due to a bad power cable connection, but not incorrect
drive replacement, repair the connection and press
F2.
If the message is not eliminated by pressing
F2,
run Array
Diagnostic Utility to resolve.
-Or-
If this message was not due to a bad power cable connection and no drive replacement took place, this could indicate
noise on the data cable. Check cable for proper routing.
-Or-
If this message is due to a defective SCSI cable, replace the cable.
continued