Home » D-Link Manuals » Hubs & Switches » D-Link DES-3828 » Manual Viewer

D-Link DES-3828 Product Manual - Page 366

config double_vlan, config double_vlan <vlan_name> {[add [uplink | access]

UPC - 790069276811

Add to My Manuals
Save this manual to your list of manuals

Page 366 highlights

xStack DES-3800 Series Layer 3 Stackable Fast Ethernet Managed Switch CLI Manual config double_vlan Purpose Syntax Description Parameters Restrictions Used to config the parameters for a previously created Double VLAN on the Switch. config double_vlan {[add [uplink | access] | delete] | tpid } This command is used to create a Double VLAN (service provider VLAN) on the Switch. vlan - The name of the Double VLAN to be configured. The user is to enter an alphanumeric string of up to 32 characters to identify this VLAN. add - Specify this parameter to add ports configured in the as one of the two following types of ports. • uplink - Add this parameter to configure these ports as uplink ports. Uplink ports are for connecting Switch VLANs to the Provider VLANs on a remote source. Only gigabit ports can be configured as uplink ports. • access - Add this parameter to configure these ports as access ports. Access ports are for connecting Switch VLANs to customer VLANs. Gigabit ports can not be configured as access ports. • portlist - Enter a list of ports to be added to this VLAN. A list of ports are configured by entering the first and last port of the list, separated by a dash. Multiple separate ports may be entered by separating them with a comma. delete - Specify this parameter to delete ports configured in the from this VLAN. • portlist - Enter a list of ports to be deleted from this VLAN. A list of ports are configured by entering the first and last port of the list, separated by a dash. Multiple separate ports may be entered by separating them with a comma. tpid - The tag protocol ID. This ID, identified here in hex form, will help identify packets to devices as Double VLAN tagged packets. The default setting is 0x8100. Only Administrator or Operator-level users can issue this command. Users must have the Switch enabled for Double VLANs. Example usage: To add ports 4 through 8 as access ports to the Double VLAN Trinity: DES-3800:admin#config double_vlan Trinity add access 48 Command: config double_vlan Trinity add access 4-8 Success. DES-3800:admin# 362

Section	Page
INTRODUCTION	5
Using the Console CLI	7
Command Syntax	11
Basic Switch Commands	13
Switch Port Commands	31
SNMP V3	35
PoE Commands	49
Network Management Commands	54
Switch Utility Commands	62
Network Monitoring Commands	73
Layer 2 FDB Commands	86
Packet Storm Control Commands	94
QoS Commands	98
Mirror Configuration Commands	106
VLAN Commands	109
Link Aggregation Commands	123
IGMP Snooping Commands	127
802.1X Commands (Including Guest VLANs)	135
Access Control List (ACL) Commands	148
Traffic Segmentation Commands	168
Command List History	170
Basic IP Commands (For Layer 3)	173
ARP Commands	178
Routing Table Commands	182
Route Redistribution Commands	185
RIP Commands	191
IGMP Commands	195
Auto Config Commands V3	199
DNS Relay Commands	201
DVMRP Commands	205
IP Multicasting Commands	210
MD5 Commands	213
OSPF Configuration Commands	215
Time and SNTP Commands	232
Port Security Commands	238
MAC Notification Commands	242
SSH Commands	246
Jumbo Frame Commands	254
Access Authentication Control Commands	256
D-Link Single IP Management Commands	279
Multiple Spanning Tree Protocol (MSTP) Commands	289
SSL Commands	301
VRRP Commands	307
System Severity	316
DHCP Relay	318
IP-MAC Binding Commands	324
LACP Configuration Commands	338
CPU Interface Filtering (Software ACL) Commands	340
Modify Prompt and Banner Commands	348
Safeguard Engine	351
WRED Command List	353
Web-based Access Control (WAC) Commands	357
Double VLAN Command List	363
Limited Multicast IP Address Commands	368
Route Preference Commands	373
MAC-Based Access Control Commands	376
PIM Commands	385
Loopback Interface Commands	402
DHCP Server Command List	405
MLD Snooping Commands	421
Loopback Detection Commands	428
Password Recovery Commands	433
Multicast VLAN Commands	436
CPU Filtering Commands List	439
Broadcast Segmentation Commands	441
Technical Specifications	443

Match case Limit results 1 per page

xStack DES-3800 Series Layer 3 Stackable Fast Ethernet Managed Switch CLI Manual

362

config double_vlan

Purpose

Used to config the parameters for a previously created Double VLAN

on the Switch.

Syntax

config double_vlan <vlan_name> {[add [uplink | access] |

delete] <portlist> | tpid <hex 0x0-0xffff>}

Description

This command is used to create a Double VLAN (service provider

VLAN) on the Switch.

Parameters

vlan <vlan_name 32>

- The name of the Double VLAN to be

configured. The user is to enter an alphanumeric string of up to 32

characters to identify this VLAN.

add –

Specify this parameter to add ports configured in the

as one of the two following types of ports.

•

uplink

– Add this parameter to configure these ports as

uplink ports. Uplink ports are for connecting Switch VLANs

to the Provider VLANs on a remote source. Only gigabit

ports can be configured as uplink ports.

•

access

- Add this parameter to configure these ports as

access ports. Access ports are for connecting Switch

VLANs to customer VLANs. Gigabit ports can not be

configured as access ports.

•

portlist

– Enter a list of ports to be added

to this VLAN. A

list of ports are configured by entering the first and last port

of the list, separated by a dash. Multiple separate ports

may be entered by separating them with a comma.

delete -

Specify this parameter to delete ports configured in the

from this VLAN.

•

portlist

– Enter a list of ports to be deleted from this VLAN.

A list of ports are configured by entering the first and last

port of the list, separated by a dash. Multiple separate

ports may be entered by separating them with a comma.

tpid <hex 0x0-0xffff>-

The tag protocol ID. This ID, identified here in

hex form, will help identify packets to devices as Double VLAN

tagged packets. The default setting is 0x8100.

Restrictions

Only Administrator or Operator-level users can issue this command.

Users must have the Switch enabled for Double VLANs.

Example usage:

To add ports 4 through 8 as access ports to the Double VLAN Trinity:

DES-3800:admin#config double_vlan Trinity add access 4-

Command: config double_vlan Trinity add access 4-8

Success.

DES-3800:admin#